Official Truck Builders CAD Model Library
- Thread starter MTD
- Start date
jgmx893
New member
Definitely would be. I might try to design some hub caps or something. Maybe some sort of mount for a scangauge too.
jgmx893
New member
I'm adding a model for any led voltmeters like this one since there's a bunch on amazon using the same exact shape: Hittime Mini DC 0V To 99.9V Red LED Digital Panel Volt Voltage Meter Voltmeter - - Amazon.com
The way it works is that it's just a bracket that pins it up against the headboard in the top left corner of the windshield. The hooks on top slide under the headboard. This might be kind of confusing, I can post pics if needed.
Right now I just have a makeshift mount but designed this so I can 3d print it.
The way it works is that it's just a bracket that pins it up against the headboard in the top left corner of the windshield. The hooks on top slide under the headboard. This might be kind of confusing, I can post pics if needed.
Right now I just have a makeshift mount but designed this so I can 3d print it.
Desert Fox
New member
Here is an idea and I will be glad to get measurements if someone wants to design it.
The seats in FJ Cruiser are to low. There is not an aftermarket riser for these seats. Looking at it I don't see it being a big deal to make. But then I am not an engineer or designer.
The problem is the front bracket bolts in at an angle. The back is parallel to the floor but the front is at an angle.
Is anyone up for this?
I can get it made if I have the design.
The seats in FJ Cruiser are to low. There is not an aftermarket riser for these seats. Looking at it I don't see it being a big deal to make. But then I am not an engineer or designer.
The problem is the front bracket bolts in at an angle. The back is parallel to the floor but the front is at an angle.
Is anyone up for this?
I can get it made if I have the design.
snivilous
Senior Member
Need pictures, measurements, and 20% profit
By the way I had to brag I've now upgraded to SolidWorks 2014 Premium :guitar3: With that said I hate SolidWorks, specifically that none of the versions are cross compatible (even backwards compatible wtf) without saving it as a none SW file. So stupid and a cheap way to make people spend more.
Desert Fox
New member
Need pictures, measurements, and 20% profit
By the way I had to brag I've now upgraded to SolidWorks 2014 Premium :guitar3: With that said I hate SolidWorks, specifically that none of the versions are cross compatible (even backwards compatible wtf) without saving it as a none SW file. So stupid and a cheap way to make people spend more.
You can have all the profit, I just want to raise up the seats in our FJ. But there is a market for it. Plenty of head room in the FJ and raising the seat gives better visual over the hood.
I will get some angles and measurements.
MTD
New member
Need pictures, measurements, and 20% profit
By the way I had to brag I've now upgraded to SolidWorks 2014 Premium :guitar3: With that said I hate SolidWorks, specifically that none of the versions are cross compatible (even backwards compatible wtf) without saving it as a none SW file. So stupid and a cheap way to make people spend more.
I have 2014 as well now that's why I always upload a step file along with the solid works file. Just something to keep in mind.
As for the seat risers I'll take a crack at it too since I am buying another printer shortly here lol
MTD
New member
No shits given here I don't have a ton of time. We could double team it for all I Care lol
jgmx893
New member
Gonna print this out this week at school. If it turns out well I'll add it to the library. I actually printed one out that was supposed to have "t4r.org" in raised lettering on it but it was too big, my hand just didn't fit comfortably around it. This one should fit perfectly into your palm, and it might even be a little small.
The translucent view showing where it slides down a bit and then the 8mm part starts. No threads in it but it's snug enough to where it threads itself well with minimal effort.
The old design that was too big:
The translucent view showing where it slides down a bit and then the 8mm part starts. No threads in it but it's snug enough to where it threads itself well with minimal effort.
The old design that was too big:
Last edited:
MTD
New member
You gonna upload these badboys? :happy:
jgmx893
New member
3D Printed Spacer Lift?
Anyone have insight to if this would work? I have CAD'ed up a 5/8" spacer for my 4th gen to give around 1" of lift up front and was thinking about 3D printing it. The only reason I'm considering this is because I could get the spacers printed for free. It would be solid ABS plastic, no filling/bracing inside. I'm wondering how it would hold up to temp. changes, dirt, and the extreme pressure of the spring. I don't know enough about ABS to answer any of these questions, so I'm hoping someone else on here has insight.
Anyone have insight to if this would work? I have CAD'ed up a 5/8" spacer for my 4th gen to give around 1" of lift up front and was thinking about 3D printing it. The only reason I'm considering this is because I could get the spacers printed for free. It would be solid ABS plastic, no filling/bracing inside. I'm wondering how it would hold up to temp. changes, dirt, and the extreme pressure of the spring. I don't know enough about ABS to answer any of these questions, so I'm hoping someone else on here has insight.
MTD
New member
If you send me the file I can run a quick FEA on it?
MTD
New member
Export as a .step file if possible. I can convert it to a solidworks file easily then.
MTD
New member
From the results in this simulation it looks like you should be okay with a soild fill spacer. Keep in mind though that even though there is about a factor of safety of 2 on this model it doesn't specifically dictate how a 3d printed part will act since the model is "solid". For all we know the woven patter of a 3d printer could be stronger in compression, but we don't know. So just use this as a guideline and keep an eye on them after they are installed.
Similar threads
