There is two loops on each side of the handle to put the factory screw through!
-
If you plan to post to Classified forums, you must follow these rules, or your post will be deleted.
- Thread title must include at a minimum: FS or FT, Item(1st, 2nd, 3rd, 4th or 5th gen), Price and Location. For Example: FS: 4th GEN Carpet Floor Mats - Tan, $50 Denver, CO.
-
All Threads must contain the following information
- What is for sale/trade (model, specs, etc.)
- Condition
- Price/What you want to trade for
- Location of item
- At least one picture of the item for sale or for trade
- No "Feeler" Threads - Its either for sale or it isn't.
- Moderators lock Classified Threads that have not had any activity in 90 days or when the part is announced SOLD.
- Threads not complying with the rules will be deleted without notice.
Paracord Grab Handles - Ohio
- Thread starter 08yoter
- Start date
There is two loops on each side of the handle to put the factory screw through!
I shipped some handles out to asakite and his runner is a 5th gen! Maybe he can give some input
AsAkite
Member
So for any 5th Gen owners wondering if this will work, I gave the suggestion by Toy2G a try and I think after adding a "yet to be figured out" piece of cosmetic trim, it will work nicely. as far as strength of the anchors, I did give it a good tug but didn't hang off it or anything. I am going to wait to do the other 3 after I figure out what I am going to do about the cosmetic pieces I will need to cover the exposed parts. Also probably get smaller washers as you really wont need much, the hoops on the handles are just big enough to slide the screw through.
.
.
.
.
AsAkite
Member
As far as adding one to the pillar where Toyota so rudely stopped including one, I can't help as I am only adding these to the over heads.
Sorry.
-S
agllkieumho
New member
They look good installed!So for any 5th Gen owners wondering if this will work, I gave the suggestion by Toy2G a try and I think after adding a "yet to be figured out" piece of cosmetic trim, it will work nicely. as far as strength of the anchors, I did give it a good tug but didn't hang off it or anything. I am going to wait to do the other 3 after I figure out what I am going to do about the cosmetic pieces I will need to cover the exposed parts. Also probably get smaller washers as you really wont need much, the hoops on the handles are just big enough to slide the screw through.
.
.
AsAkite
Member
So finding a thin square washer large enough to cover the exposed area, but has an internal diameter that isn't too big is harder than I thought it would be. I got this one thats thicker on one side as a temp solution until I can figure out something better. Not sure I trust the strength of the handle since the screw doesn't go as far into the anchor, but It will work cosmetically until I change it.
.
.
RedSled
New member
Hey 08yoter, the pull handles for my rear seats got here last week. Finally got them put in with just a couple glitches, no big deal really. Had to drill the bracket hole out to 1/4" for the mounting screw, and the pulls ended up being almost 12" long with the bracket, I was looking for 9" over all, but I can live with it just fine. Here are a couple of pics.
Attachments
I can make you anothe set at 9inch including the bracket without a problem and get them shipped out. That never even crossed my mind man!
RedSled
New member
No need to do that man, but thanks for offering. I'm good with it. Thanks.
blakjack23
New member
I ordered a pair of the headrest handles from 08yoter and received them in the mail two days later. Great quality and they really help my daughter get in and out of her carseat. :thumb3:
Similar threads
