Parting 2000 4Runner Limited 4WD Marysville, WA

[saurkraut]

Ok, please let me know if you find one. Is the flap supposed to be on the outside? I put my hand up there yesterday and couldn't feel a flap. If it's a WA rig, I'm sure it's in better shape than one from here with the heat we get. I found it for $32 on a dealer site so I may just do that. I'm going to pull the inner panel and see if there is a flap there. I'm getting a huge amount of fine dirt and silt from the roads around here. Makes it hard to breath.

 

[DeathCougar]

Ok, please let me know if you find one. Is the flap supposed to be on the outside? I put my hand up there yesterday and couldn't feel a flap. If it's a WA rig, I'm sure it's in better shape than one from here with the heat we get. I found it for $32 on a dealer site so I may just do that. I'm going to pull the inner panel and see if there is a flap there. I'm getting a huge amount of fine dirt and silt from the roads around here. Makes it hard to breath.

[MENTION=116990]saurkraut[/MENTION] Yes I Have one in good shape, rubber is intact. The flap is on the outside of the vent. Lets cabin air pressure out, but not in.

$20 shipped

Paypal [email protected]

Thanks!
Josh

 

[Squegles]

How much for the 2 buttons on the side of the driver seat for adjusting them?

Located in Portland, OR.

 

[DeathCougar]

Guys, PLEASE do not have me go through the trouble of looking for a part, taking pictures, pulling and getting you a shipping quote, agreeing on a price, then backing out at the last second. It's very frustrating, especially having this happen by the same member twice now. Either you want to buy it, or you don't!

 

[DeathCougar]

How much for the 2 buttons on the side of the driver seat for adjusting them?

Located in Portland, OR.

[MENTION=130002]Squegles[/MENTION] I have these, $35 shipped for the pair

 

[Squegles]

If you can do it for $25 shipped, I can get you the money ASAP.
Also, do you have the little button above the 'P' in front of the shifter?

Thanks!

 

[DeathCougar]

If you can do it for $25 shipped, I can get you the money ASAP.
Also, do you have the little button above the 'P' in front of the shifter?

Thanks!

I'll keep them for spares for my seats, thank you for the offer though!

I do not have the button cover, the tow truck drivers always seem to lose them.

 

[JBurt]

Any chance you have some good condition drivers door weather stripping?

 

[DeathCougar]

Any chance you have some good condition drivers door weather stripping?

[MENTION=84643]JBurt[/MENTION] If I had a dollar for every one of those requests

Alas, I do not. In the 8 years I have been doing this, I have seen ONE that wasn't worn out from people dragging their feet across them. Sorry bud :/

 

[North]

What color is the license plate surround on this one? If it's gray, I'm interested.

 

[DeathCougar]

What color is the license plate surround on this one? If it's gray, I'm interested.

[MENTION=60421]North[/MENTION] I currently have someone interested, but if they back out I will let you know

 

[thursdaymike]

I need front passenger brake line that comes right off the caliper. Its a hard line.

 

[DeathCougar]

I need front passenger brake line that comes right off the caliper. Its a hard line.

$25 shipped

 

[plifshiz]

Lumbar support switch to 30097?

 

[DeathCougar]

Lumbar support switch to 30097?

Only good one I've ever seen was the last new tan one in the country that I bought. Sorry. Worst design ever

 

[99SC4Runner]

Do you have any of the following parts;

1. Ash tray and bracket with the light bulb socket
2. lighted ign switch key ring with wiring connector
3. dash bezel with clock
4. lighted cigarette lighter socket with wiring connector

 

[Blind Cleric]

4runner parts

I'm looking for gray head rests for rear seats, and driver's side tail light plastic.

 

[DeathCougar]

Do you have any of the following parts;

1. Ash tray and bracket with the light bulb socket
2. lighted ign switch key ring with wiring connector
3. dash bezel with clock
4. lighted cigarette lighter socket with wiring connector

I have all these parts. Are you trying to convert to 99+ style? And does it need to be limited (woodgrain) or just sr5 (black)

I'm looking for gray head rests for rear seats, and driver's side tail light plastic.

No headrests

Taillight $35+ship

 

[99SC4Runner]

I have all these parts. Are you trying to convert to 99+ style? And does it need to be limited (woodgrain) or just sr5 (black)

This is for my 96 Tacoma, so I need them in black SR5 style.

I'll need the black bezel around the ign switch also, if it's the same as my Tacoma.

Let me know.

Thanks.

 

[DeathCougar]

Bump!