Pelfreybilt - See Update on Last Page

Status
Not open for further replies.
OatBunch said:
This looks amazing. I love the fact that it is a full replacement, and that the swing arms are removable, but how much of a PITA would they be to remove? And are you exposing other areas that you may not want open? I imagine it wouldn't be too hard to fab up a filler plate for when they are off, based on the most recent renderings.
Click to expand...

LawnDart said:
I don't believe they're intended to be something you take on and off a lot.

Frankly for people not used to swing arm bumpers you'll almost assuredly leave them on 100 percent of the time. You get used to them pretty quickly.
Click to expand...

The gates weren't intended to be removed often or very easily. Yes - they can be removed if needed but we don't recommend pulling them off.

-Pelfreybilt
www.pelfreybilt.com
 
Coler2002 said:
Is there any provision for a backup cam? I am sure its not to hard to fab one up but would be cool it was built in.
Click to expand...

We will be including an option for customers to maintain their backup camera if desired. Stay tuned - more photos and details will come available as this goes into production.

-Pelfreybilt
 
T4R Money Pit said:
I do like the new renderings as well!!! In my experience with cans mounted higher (on my CJ and FJ) refueling the vehicle tank was a super simple gravity syphoning process without pulling cans. Keeping the center of gravity as low as possible however is a definite plus that I can appreciate and more important whenever possible. There are always other ways to refill without pulling a can.

If you know, will the cans be high enough in this mounting position to still facilitate a gravity syphon refill?

As a sidebar question, and I am in no way trying to sound negative or contrary, I swore I would never go back to a swing-out mount after having one on my FJ. It was great at first but after a short time it became a rattle nightmare that I never learned to love off-road.

Do we know anything more at this point about how these swing-outs will lock-up to hold themselves in place and how rigid the swings will remain in the closed position when loaded? I am trying to talk myself into the idea versus the non-swing version (after previously swearing never again).
Click to expand...

Based on the current measurements it doesn't look like a gravity siphon will work since the base of the can will be quite a bit lower than the gas cap.

We will have more details on the hinge and latch assembly as soon as production gets started (very soon). We are building these to handle abuse on and off the trails. We don't like things that rattle, clunk, or pop.
 
Mikey6863 said:
Are there plans to bring a completed bumper to Expo West? Would love to see it, renderings look fantastic!
Click to expand...


pelfreybilt said:
Let me double check with the team and get back to you. At the very least the non-swingout bumper will probably be there. Thanks!
Click to expand...

My apologies about the delay. We will certainly have one at Overland Expo West! We will also be showing off some other new goodies.

Stop on by! (Spot A1)

Pelfreybilt - High Quality Off-Road & Overland Toyota Components
 
Will there still be room for the factory spare underneath, in case we're on a long trip and want two spares (and don't want to put one up top)?

Removability - I know from your previous posts that this wasn't a priority, and I get it from a design stability perspective why that's the case . . . and there's probably not a real answer you can give here on my dilemma. . . but sharing anyway, because I'm sure many in here face the same dilemmas.

I live in PB, so my T4R doesn't fit in my garage, so I have to parallel park most of the time and the swing-outs will hinder access to surfboards, wetsuits, etc. . .

I plan to overland maybe 1 or 2 times per year, so the swing-outs would be GREAT for that limited use. . . The rest of the time it's hitting local SD trails or deserts, mountain biking, surfing, etc. where I don't really need that much stuff.

So just how big of a PITA is it really gonna be to remove and replace? . . . lol . .

Yes. . . I want my cake, and I want to eat it too!!!

Also, is your shop open to the public? Living in SD, I'd love to come take a look . . . I have your sliders, want that front alum bumper, and in my opinion, your stuff has the best fitment and look of any of the other brands out there. . .huge fan!
 
Wigglepuppy said:
Will there still be room for the factory spare underneath, in case we're on a long trip and want two spares (and don't want to put one up top)?

Removability - I know from your previous posts that this wasn't a priority, and I get it from a design stability perspective why that's the case . . . and there's probably not a real answer you can give here on my dilemma. . . but sharing anyway, because I'm sure many in here face the same dilemmas.

I live in PB, so my T4R doesn't fit in my garage, so I have to parallel park most of the time and the swing-outs will hinder access to surfboards, wetsuits, etc. . .

I plan to overland maybe 1 or 2 times per year, so the swing-outs would be GREAT for that limited use. . . The rest of the time it's hitting local SD trails or deserts, mountain biking, surfing, etc. where I don't really need that much stuff.

So just how big of a PITA is it really gonna be to remove and replace? . . . lol . .

Yes. . . I want my cake, and I want to eat it too!!!

Also, is your shop open to the public? Living in SD, I'd love to come take a look . . . I have your sliders, want that front alum bumper, and in my opinion, your stuff has the best fitment and look of any of the other brands out there. . .huge fan!
Click to expand...

The spare will fit in the factory location. Our corporate cruiser still has the oversized spare tucked underneath here:

39135036620_d857c5c9d3_h.jpg


As we get closer to entering production we'll have a better idea of the "removability" of the rear gate although it probably won't be easy.

Since you are local, we welcome you to stop by the shop and check everything out! We are always happy to talk Toyotas. We appreciate the support!

Pelfreybilt - High Quality Off-Road & Overland Toyota Components
 
comtn4x4 said:
How far behind? For those of us that have them ordered in would be good to know
Click to expand...

Not a major concern for those that have ordered. Our estimated lead times are the same and the ETAs we've provided will remain. Our goal was to start production at the end of March but it's been pushed back slightly.

Please contact us directly if you have any concerns about your order.

-Pelfreybilt
Pelfreybilt - High Quality Off-Road & Overland Toyota Components
 
Status
Not open for further replies.

Similar threads

mrbrenan
Beatty Metal Works Rear Winch Bumper for 5th Gen 4Runner
Replies
2
Views
1K
jdm-v35
J
rpjtremblay
FOR SALE, OG 5th Gen 2013 4Runner Limited Overland Build, $22.5k, New Jersey
Replies
0
Views
2K
rpjtremblay
rpjtremblay
KwonRunner
FS: 4th Gen 2008 Toyota 4Runner V6 4WD – 194K – Modified – $25,900 OBO – NorCal
Replies
0
Views
126
KwonRunner
KwonRunner
0
FS 3rd Gen 2000 SR5- Phoenix, AZ $8000- Sold
Replies
2
Views
4K
004runnerPhx
0
obkook
FS: 1997 Toyota 4Runner – $19500 - CA-Legal 1KZ-TE Turbo Diesel – Smog Exempt
Replies
0
Views
191
obkook
obkook

Members online

Total: 579 (members: 1, guests: 578)

Forum statistics

Threads
278,316
Messages
3,554,113
Members
248,016
Latest member
Advally Service

Share this page

Trending content

Back
Top