Satoshi Grill Mod - 5th Gen

Anyone have a good place to get the TOYOTA emblem? ToyotaPartSales.com sez they are discontinued and cannot get them.
 
What a pain it is to get this section out. Grillcraft has instructions but they totally skipped a few steps.

Grillcraft® - Genuine Sport Grilles - Installs

I got the parts in today and made an attempt to get it out. I got everything off except the actual removal from the lower bumper. I know someone said there were clips by the headlights, but man I cannot figure it out for the life of me.

Put everything back together and that's it for me today.
 
I had the same issue when doing my driving lights.

The two clips on each side closest to the headlights are very hard to release. I think I spent almost an hour on those clips alone. I ended up kinda pushing the bumper with my hip and trying to release the clips, eventually they came free and the rest of the bumper basically fell off.

edit: here's the pic from the repair manual if needed...
bumper.png~original
 
Last edited:
reklov said:
What a pain it is to get this section out. Grillcraft has instructions but they totally skipped a few steps.

Grillcraft® - Genuine Sport Grilles - Installs

I got the parts in today and made an attempt to get it out. I got everything off except the actual removal from the lower bumper. I know someone said there were clips by the headlights, but man I cannot figure it out for the life of me.

Put everything back together and that's it for me today.
Click to expand...

I saw those Grillcraft instructions and the hard parts they left out.:spider: They were probably cussing like a sailor then instead of shooting pics! I tried it like that one time and those clips are a b*tch to see and get to when the bumper cover is on.

This is just my opinion from doing it a bunch of times.....I personally think it's easier to take the whole front bumper cover off as one piece and then separate the upper grill.I've had mine off 5-6 times already and can take it off in less then 10 minutes with an air ratchet. You have to watch though on how tight you put the screws/bolts in when you put this back together as the nuts are plastic and strip real easy. I put them back in by hand with a 1/4 inch ratchet and I think they are all 10 mm heads.

Take all the bolts/clips out per the oem repair manual drawings and unplug fog/turn signal lights .

Pull outward near the wheel wells where it shows 3 each bolts and 3 clips to release it from the inner fender liner and fender.It's sort of sandwiched in between the liner. Pay attention here to how it fits together so when you put it back on! There is also a 1/8" thick piece of double sided foam holding it at the corner of the headlight.

Then grab underneath in the middle and pull forward and up to release those clips in front of the headlights sort of like it's hinged upward . You'll should feel them release, then it should come off forward.

Then when the whole front bumper cover assembly is off you can see and get to the clips that hold the upper grill to the bumper cover.
 
Last edited:
same here, it was a pain to get the stock grill off. just keep pushing/pulling on those clips by the headlights. once you get one released the rest comes off easy. and snaps back in like nothing.
 
Jesse1983 said:
same here, it was a pain to get the stock grill off. just keep pushing/pulling on those clips by the headlights. once you get one released the rest comes off easy. and snaps back in like nothing.
Click to expand...

Agreed. I know this sounds bad, but just pull on it til the bumper starts flexing, o and wear gloves. I had my finger in by one of the tabs, and when I pulled it off, the tabs cut my finger real bad.
 
adio3x said:
I have a spare satoshi grille (almost done) if anyones interested in it. PM me.
Click to expand...

By chance do you have the OE Trail insert (in black) that you cut out, or did you use and SR5 grill? I have an SR5 w/ chrome and want to swap for black.
 
What a PITA it is to get off that grill! Anyway, the Satoshi Grill is officially finished and I'll be sure to post some pictures tomorrow! :bigok:
 
apenso said:
By chance do you have the OE Trail insert (in black) that you cut out, or did you use and SR5 grill? I have an SR5 w/ chrome and want to swap for black.
Click to expand...

Sorry, I just have 2 spare SR5 grilles. Why don't you just take it off and spray if flat black? Probably save you some money.
 
Mason said:
Is that the grill from the previous links (I think Jesse1983 posted it), or is it a grill craft?
Click to expand...

Yes it is the same grill as they used (and not the GrillCraft). Takes some time to cut it down and get it just right, but the time spent was def worth it. :D
 
ThirdToy said:
Here ya go...
Click to expand...

Wow ThirdToy! You nailed it! Great job:bravo:

adio3x said:
Sorry, I just have 2 spare SR5 grilles. Why don't you just take it off and spray if flat black? Probably save you some money.
Click to expand...

apenso said:
The paint wont hold up like the Trail black plastic..
Click to expand...

Ya, you never know how many rock and sand nicks you get on the front til you paint something black over chrome!

On a side note or idea , I read on other forums that either paint stripper or some used easy off oven cleaner on chrome painted plastic to remove it clean.Under the chrome paint is plain black plastic just like the TE ones. It would have to be done before any sanding ,like I already did on mine or else the black plastic would be all scratched up.

Might be worth a shot to try when someone has a chromed piece that is junk anyways from the Satoshi mod. Heck , we might be able to strip the paint from all the chromed parts instead of painting! It's just black ABS plastic under the paint.

We have some industrial stripper here at work in 55 gallon drums that doesn't harm the fiberglass parts underneath and so probably wouldn't harm abs plastic.Just dab it on and 5 minutes later the paint peals off.
 
harper7 said:
Wow ThirdToy! You nailed it! Great job:bravo:
Click to expand...

Thanks Gary! Hope ya don't mind I copied you with the Piaa 510's as well :hello:

KevinG said:
Very well done!

Heading there tomorrow...hopefully I still have some spare $ left to do this mod :tongue:
Click to expand...

Thanks Kevin! Yea I actually live less than 2 minutes from Mohegan Sun. That picture I posted is from the end of my driveway. :banana:
 
You must log in or register to reply here.

Similar threads

Iceknight366
FS (5th Gen): RCI A-Arm Lower Control Arm Aluminum skid plates-$219.99 - San Jose, CA
Replies
0
Views
708
Iceknight366
Iceknight366
T
FS: 2007 4th Gen SR5, 8,500, Chicago, IL
Replies
6
Views
4K
dmuniz1219
D
Fiffa
FS: 3rd Gen 4Runner Limited, Vancouver, WA, $13k OBO
Replies
2
Views
3K
Fiffa
Fiffa
B
2015 5th gen Steering vibration/shimmy
Replies
0
Views
4K
Brian Wilson
B
mrbrenan
Beatty Metal Works Rear Winch Bumper for 5th Gen 4Runner
Replies
2
Views
1K
jdm-v35
J

Members online

Total: 1,343 (members: 5, guests: 1,338)

Forum statistics

Threads
278,312
Messages
3,554,085
Members
248,016
Latest member
Advally Service

Share this page

Trending content

Back
Top