Toyota OKs Use of Imperfect Parts to Keep Production Going

[T4R_Canuck]

I actually think that this is a very reasonable step to take in the current supply chain environment, where companies are struggling to get parts.

Lets be honest, these parts that will now be accepted by Toyota will still likely be of a higher quality than the average equivalent part of a RAM/Fiat or GMC/Chev vehicle. I've literally sliced my finger open on the edges of dashboards and trim pieces on a few Jeeps and trucks i've owned, or been a passenger in, so obviously those parts met QC standards in those factories.

 

[BorotHex]

I actually think that this is a very reasonable step to take in the current supply chain environment, where companies are struggling to get parts.

Lets be honest, these parts that will now be accepted by Toyota will still likely be of a higher quality than the average equivalent part of a RAM/Fiat or GMC/Chev vehicle. I've literally sliced my finger open on the edges of dashboards and trim pieces on a few Jeeps and trucks i've owned, or been a passenger in, so obviously those parts met QC standards in those factories.

GM is a lot better than it was 10 years ago. I had a 2019 Trail Boss that honestly had much better initial quality than my 4Runner. I traded it with 15,000 miles, so I don’t know the long term, but the 5.3L V8 is pretty bullet proof. It did have a very faint clunk in the rear end coming to a stop sometimes, but I figured the shaft probably needed to be greased or something simple. The interior was silent, which is absolutely not the case with my 4Runner. Interior quality is night and day in favor of the Chevy.

Never owned a Jeep, Dodge, or Chrysler. Never will either.

 

[2021nightshade4x4]

GM is a lot better than it was 10 years ago. I had a 2019 Trail Boss that honestly had much better initial quality than my 4Runner. I traded it with 15,000 miles, so I don’t know the long term, but the 5.3L V8 is pretty bullet proof. It did have a very faint clunk in the rear end coming to a stop sometimes, but I figured the shaft probably needed to be greased or something simple. The interior was silent, which is absolutely not the case with my 4Runner. Interior quality is night and day in favor of the Chevy.

Never owned a Jeep, Dodge, or Chrysler. Never will either.

GM couldn’t build an interior to save their life until about 2015.

Once they mastered that, unfortunately the motors went direct injection. IMHO they got worse after about that time. Both 5.3 and 6.2. And lifter issues. And transmission issues with 8L90, 10L100, all crap. Joint venture was a mistake.

Give me a 6 speed Allison. Give me about a ‘05 Duramax. Even an 8.1L.

Ironically Chryslers have been great. 1995 JGC 4.0L, 1999 Durango 5.2L, 2004 Durango 5.7L. All over 220k miles. Only complaint is the newer Durango started draining batteries when I tried to put a factory nav unit in it. My fault shouldn’t have tried to buy one off of Facebook Marketplace LOL

Now the 42RE last 225k before rebuild, 44RE at 290k all original, and 545RFE is at 227k all original. I don’t tow anything so that might help.


Sent from my iPhone using Tapatalk

 

[Gstick]

GM couldn’t build an interior to save their life until about 2015.

Once they mastered that, unfortunately the motors went direct injection. IMHO they got worse after about that time. Both 5.3 and 6.2. And lifter issues. And transmission issues with 8L90, 10L100, all crap. Joint venture was a mistake.

Give me a 6 speed Allison. Give me about a ‘05 Duramax. Even an 8.1L.

Ironically Chryslers have been great. 1995 JGC 4.0L, 1999 Durango 5.2L, 2004 Durango 5.7L. All over 220k miles. Only complaint is the newer Durango started draining batteries when I tried to put a factory nav unit in it. My fault shouldn’t have tried to buy one off of Facebook Marketplace LOL

Now the 42RE last 225k before rebuild, 44RE at 290k all original, and 545RFE is at 227k all original. I don’t tow anything so that might help.


Sent from my iPhone using Tapatalk

I agree about the GM interiors, but am happy with the 6.2 LS3 & Tremec TR6060 in my 15' Camaro SS/1LE. (this will be the last GM vehicle that I'll ever own) The 16' & up LT1's have more HP & TQ, but the Direct Injection is just another maintenance cost.

 

[Dzldust]

You mean like the years of thin paint and thin weak windshields ? Gotta have saved some money on paint as thin as it is on my 21 4runner