Weld together front bumper kit?

Howitzer said:
It would appear so, sadly. Did anybody end up buying/receiving any of these kits? Pics? The DIY kit was a neat idea. Like it was said, lots of folks have welders, but not tube benders and plasma cutters; myself included
Click to expand...

I would have been happy to get a front and a rear. I also have a welder but lack the other stuff
 
Howitzer said:
It would appear so, sadly. Did anybody end up buying/receiving any of these kits? Pics? The DIY kit was a neat idea. Like it was said, lots of folks have welders, but not tube benders and plasma cutters; myself included
Click to expand...

Yep, I'm in the same boat.
I decided to just build my own plate bumper. Got it all mocked-up in foam board, about to start cutting the steel.
 
Scalded_Dawg said:
Yep, I'm in the same boat.
I decided to just build my own plate bumper. Got it all mocked-up in foam board, about to start cutting the steel.
Click to expand...

Would you be able to post some pictures? Or, if you're so inclined, do a semi-writeup on it? I would love to see progress, and the steps you took. That is; unless it a proprietary secret ;) Fabricating is like making a sandwich; everyone does it differently and takes different steps, has different approaches and executes differently, and I believe that it would be beneficial to see your "views" on it.
 
walrusmt said:
Yes I saw the CBI also, but the price was a few hundred. The original post that started this thread is DOA. I don't think they could have bought and cut the steel for what they were charging and been able to make a living. 2nd Gen bumpers are either tubes, or stupidly expensive. Ugh.
Click to expand...

The original post is CBI. I must be missing something.
 
Howitzer said:
Would you be able to post some pictures? Or, if you're so inclined, do a semi-writeup on it? I would love to see progress, and the steps you took. That is; unless it a proprietary secret ;) Fabricating is like making a sandwich; everyone does it differently and takes different steps, has different approaches and executes differently, and I believe that it would be beneficial to see your "views" on it.
Click to expand...

I need to make a build thread anyway… guess I could start it off with this front bumper.
 
Howitzer said:
Would you be able to post some pictures? Or, if you're so inclined, do a semi-writeup on it? I would love to see progress, and the steps you took. That is; unless it a proprietary secret ;) Fabricating is like making a sandwich; everyone does it differently and takes different steps, has different approaches and executes differently, and I believe that it would be beneficial to see your "views" on it.
Click to expand...

Scalded_Dawg said:
Yep, I'm in the same boat.
I decided to just build my own plate bumper. Got it all mocked-up in foam board, about to start cutting the steel.
Click to expand...

OR, OR….. if ya wanna make two…..i'm close by in NC lol.
 
ralatkins said:
OR, OR….. if ya wanna make two…..i'm close by in NC lol.
Click to expand...

Ha Haa! Nice try. I cut all the pieces today… I don't have a plasma torch or even a cutting torch, so it was all 4 1/2" cutting wheel… slow rough going, but it's done.

I'll do a write-up of sorts for this bumper build; as I'm not ready to start a truck build thread.
 
where do I send the check ?

I think that thing looks killer.
I am soooo tired of seeing the same ones all over town.
I went with the stock setup just so I wouldn't look like everyone else!
 
Stumbled across this old thread. If you are making these kits I might be interested in one for a 1st gen. I really like the look
 
I dunno if CBI is still doing these bumpers, but here's their info if you wanna call them directly:

Contact Information:
Toll Free: 866-522-0697
Local Calls: 208-522-7000
208-528-0664
Fax #: 208-522-7062
Email: [email protected]
Business Hours of Operation:
Monday – Friday 8:00AM to 5:00PM (MST)
Saturdays: By appointment & Email Only
Sundays: Email Only
CBI Offroad Fab is located at:
CBI Offroad Fab
3180 N. Wright Rd.
Idaho Falls, ID 83401
- See more at: Contact CBI Offroad For Your Next Custom Offroad Project
 
Old thread but figured I'd add what I offer for the classic T4R's for weld-together kits. We currently have front bumpers and full drivetrain skids for the 1st and 2nd gen 4runners and plan to release a rear bumper with single and dual tire swing out options.

All of our bumpers are made to provide the best possible approach angle and ground clearance while still being able to fit a winch. And of course, they are available with no tubing or just a small center hoop for those who don't like the full headlight tubing look.

https://www.coastaloffroad.com/


IMG_5707 by Brandon Faliszewski, on Flickr
IMG_5686 by Brandon Faliszewski, on Flickr
IMG_5726 by Brandon Faliszewski, on Flickr
IMG_5666 by Brandon Faliszewski, on Flickr
IMG_5668 by Brandon Faliszewski, on Flickr
 
Last edited:
You must log in or register to reply here.

Members online

Total: 246 (members: 3, guests: 243)

Forum statistics

Threads
278,309
Messages
3,554,071
Members
248,016
Latest member
Advally Service

Share this page

Trending content

Back
Top