What Did You Do To Your 3rd Gen Today?

[73Duster440]

It is awesome to have my baby back after parking it over a week ago after losing brakes. Pull past my driveway as I always do to back in. I stop then start to back up and as I hit the pedal to slow down to hit the miami curb at the end of the driveway she just keeps rolling. :frusty:

I got an A1 Cardone booster and new Toyota master cylinder all swapped in.

The brakes have never felt this good. :reddance:

Next to get working on my fuse box install

 

[Cree]

Picked up a set of Tundra wheels with tires for 250. The paint is rough, but it doesn't matter since I'm going to refinish them anyway.

 

[4Runner4Leon]

Ordered a set of Falken Wildpeak A/T3W's, now I just sit and wait .

Also was excited to replace my engine label that was peeling off:



only to find that the replacement label was creased during shipment:



So, more waiting.

 

[infantry503]

Gave her a bath

 

[octanejunkie]

Installed the PCK from [MENTION=28464]eimkeith[/MENTION] along with an OME trim packer on the rear driver side coil yesterday. The truck now sits level.

Interestingly, the original OME labels are still on my rear coils; one has an A and one a B after the model number. All other markings on the stickers are the same. Wonder what that means [emoji848]

Sent from my Pixel XL using Tapatalk

 

[mikeferg]

I dont post much but I did a brake job lol

 

[jbrentd]

Installed the PCK from [MENTION=28464]eimkeith[/MENTION] along with an OME trim packer on the rear driver side coil yesterday. The truck now sits level.

Interestingly, the original OME labels are still on my rear coils; one has an A and one a B after the model number. All other markings on the stickers are the same. Wonder what that means [emoji848]

Sent from my Pixel XL using Tapatalk

The instructions that came with mine said the “A” coil goes on the drivers side.

 

[CRB Racing]

Welded on a set of CBI sliders.

 

[2ndhandyotaman]

I just drove mine, enjoying the reburb'd drivers seat. It feels like a different vehicle between the seat and new rear shocks.

 

[Kanoe]

The instructions that came with mine said the “A” coil goes on the drivers side.

My dealer handed me a printed set of Australian directions, where the driver is on the other side.

Best just to remember that the taller spring goes on our NA drivers side. Simple.

 

[TestVirus]

Listened to it not start.

 

[Mark_BC]

I washed it off the other day after the big Mexico trip and today I pulled it out into the sun to vacuum etc. I noticed several new little rock chips in the paint on the sides, really annoying. When I got it I took the running boards off which protected the sides from rocks. I have some Limited flares including the door side cladding that I'm going to stick on with 3M VHB double sided tape which should help protect it some more but I guess they won't entirely stop until I put some rock sliders on.

And those stupid rust bubbles are back on the rocker panels. Man, drive through one rainy section on the Oregon coast with salt spray for a few hours and then all the rust comes back. I drove through a rainstorm in Portland a few hours later to wash it all off.

Also some new pinstriping but that's my fault. Nothing that won't come out with a nice polish.

Has anyone got theirs wrapped with the 3M vinyl stuff? I am thinking I could just do the areas that get the abuse like the mirrors, front, and side doors.

 

[nchacon1984]

Installed the PCK from [MENTION=28464]eimkeith[/MENTION] along with an OME trim packer on the rear driver side coil yesterday. The truck now sits level.

Interestingly, the original OME labels are still on my rear coils; one has an A and one a B after the model number. All other markings on the stickers are the same. Wonder what that means [emoji848]

Sent from my Pixel XL using Tapatalk

Did weld your panhard kit yourself. I’m looking for someone that can weld it on for me.

 

[nchacon1984]

Installed new weathertech floor mats I got a decent price from a someone on Facebook. Just waiting on the cargo mat to come in. Installed the rear part of my lift along with 2nd Endlinks with energy suspension bushings. Will install sway bar bushings tomorrow along with front lift and sway bar bushings.

Been chasing a parisidic drain and I cant seem to find. Might need a second opinion. Also, had water in my rear passenger seat. Was about to tear the interior out to find it but my mom said she left my rear passenger window cracked when it rained. :frusty:

 

[thecole1098]

Put my LED light bar in. Typically, I don't like how "modern" LED lights look on these 3rd gens but this was free and I've grown to like it a lot.

 

[Renegade_Medic]

Cleaned up and painted pretty much everything for my motor swap. Almost ready to go in.

 

[JZiggy]

Cleaned up and painted pretty much everything for my motor swap. Almost ready to go in.

Looks like you have a big problem with your oil filter! :doh:

 

[Renegade_Medic]

Looks like you have a big problem with your oil filter! :doh:

Didn't want to come off, so I stabbed a screwdriver through it and used it like a long handle. It got a beating with a wrench before that....

 

[JayRolla]

I've done nothing to my 4runner for so long. Just sits doing nothing. Maybe I should sell to someone that would appreciate and use it. Lol.

 

[fourfive]

I've done nothing to my 4runner for so long. Just sits doing nothing.

New ride?