Recent content by dat5574

Thanks, so if I get it flushed, I've read there are two types. 1). One machine that pumps new fluid through while removing old fluid on the other end gradually replacing the trans fluid. 2.) Second method includes dropping the pan and change the filter (which is better since you can see if...

Well I took it to a transmission specialist that was recommended to me by a couple mechanics. They checked the fluid, drove it but couldn't find anything or didn't see any codes except the one for the catalytic converter. One thing he said was in his experience is brown fluid in Toyotas is...

One of the codes Auto Zone read (I don't remember the code) but was suggesting "Yaw Rate Sensor" is bad. Can this be related to the shifting out of gear while decelerating from high speeds? What are the symptoms of this sensor?

Yes, I don't have them in front of me but they were related to an exhaust leak after the cat converter/O2 sensor which is a whole other issue (Bank 1 sensor 1 I think?) But nothing related to the transmission. I just made an appt. next week for a shop that specializes in them. I'll keep my...

Hi, I have 2001 4runner with automatic transmission with 150K. For some history, in 10/2012 I had the shift solenoids replaced along with all the tranny fluid at 138K miles. Now, I drive the same route every day but 3 times in the last month during my commute, while exiting off the highway...

Hi, I've got a 2002 with 132K miles. I got the P0446 code read from two places. I know there are a couple things that can be the culprit (charcoal canister, VSV valve etc). Here's a couple things that happen that I hope someone can help me pinpoint the exact cause: 1.) When I disconnect...

Can someone help with a drive belt diagram for a 2002 4runner 3.4 V6? I want to adjust the tension on the belts due to a chirpping sound to see if that fixes it. Specificially, I think it's the one closest to the ground. I'm guessing I'd have to take off the skid plate to get to it easier from...

Hi, I have 2002 4runner and want to replace the factory front struts. I bought Monroe QuickStrut Assemblies 171351L/R. When I went to install the new assembly I got the top in but the shock's lower bolt hole seems about an inch longer than it's supposed to and I can't get it lined up with the...

How tough was it? I see Monroe has Quick Struts 171351 (R/L fronts) + Sensa Trac 37157 (rears) with a rebates right now. I'm really tempted to try this. A Cleveland, OH chain outfit quoted me $775 for the entire job with alignment! It would cost me less than half (even though I'd still need...

In my Haynes manual it suggests that due to the front springs being compressed, this can be dangerous since you have to use spring compressor etc. and the assy. should be handled with care when removed. It also suggests replacing the entire shock+spring assembly may not that be much more...

I've been reading up on how to remove rotors but when I crawled under my 2002 4runner I noticed there is a solid steel line that is connected to the caliper which runs to a bracket/flexible brake line. On another post, they suggested to remove the bracket and you can then move the...

Hi, I've got a 2002 4runner. I'm noticing it pulling to the left and the steering wheel vibrating while braking (especially at higher speeds). Does the braking issue seem related to the alignment or should I be thinking it's caliper related? If so, how can I test and determine if my caliper...

Hi, I have 2002 4runner and wondering if it's realistic to accurately check the front disc pads without removing them. If have to remove them, does removing some brake fluid from from reservoir make it that much easier to open the calipers? Thanks.

I'm interested in checking my front disc brake pads and replacing them if necessary. I have the Haynes manual but are there other publications that outline this step-by-step with photos or is this about the best I can get? Seems pretty straight forward but I wanted to know if anyone...

Hi, I attached a photo of the section of my exhaust that is the source of noise and leaking exhaust between the flanges (see red arrow). This section is behind the forward catalytic converter. As I understand it, my system has a TWC (Three-way converter...which "has separate chambers, the one...