Recent content by mitfan311

I have no idea if this will work but it cant hurt. Run a can or two of seafoam through a couple of different vacuum hoses so that it will hit all cylinders. Also turn the idle adjustment screw to just past 1000rmp and see if it holds a idle after that, even if its high and holds, it might be...

So there are coil packs only on the passenger side? What is used on the driver side?

The fuel line that runs from my fuel rail to my cold start injector has cracked. Its on a 95 3.0 It was real old and brittle. I dont guess this is a part I can get from autozone? How do I go about getting the party number or can i just go to the dealer and have them find it for me? Thanks

If you think your 3.0 v6 is slow then you are correct. Its an underpowered engine. There are no real mods worth the money. If you really think you need more power swap it with a 3.4 or whatever floats your boat. But. there is an exception. Here is what I did. My 3.0 leaked oil from the valve...

I will be replacing the head gaskets on a 95 3.0vze in December and I havebnt gone over an of the manuals yet to read up on it. I was told that I would have to remove the cam shafts in order to take the heads off. Is that true? And how much of the upper engine (ie:Plenum, Fuel rails) can come...

My95 3.0vze has been running pretty good but I had found some vacuum leaks. I fixed those up and decided to check the timing. At first I couldnt even see the mark. So I adjusted the distributor until I could. I short circuited the code box (whatever) and moved it until it was 10 btdc. Now it...

I was seafoaming my 95 3.0 the other day when I could hear the faint noise of whistling. Sure enough there was a clamp missing from the intake. It was post MAF so the air was un-metered. A decent amount of air was getting in too. That would explain my crazy idle. I fixed that and between the...

So im about to replace the gaskets to the valve covers on my 95 3.0. But Im not sure what to use. This is the third time they have been replaced so ive been told. Is there any fix or advice someone could give me about how to make them last and stop leaking this time? Also,on the driver side...

I have stock 15 inch wheels. So im thinking the biggest i can fit on there. 32'' without too much rubbing.

I have a 95 4x4 4runner. And i dont know much about tires/wheels at all. But I have 15'' rims. I have been searching through and through but i cant find where nitto makes a trail or terra grappler for a 15'' wheel. Do i need to get some new wheels maybe 16'' or 17''. I dont have the money for...

If the timing belt break on a 95 will it destroy the enging or is it also like the 3.4Lt and is safe? Thanks

I have a 95 v6 with about 220000 miles. The engine was rebuilt at about 110000. I dont have a manual or really an info on this truck. How often do the belts need changing. Thanks

I have my first 4x4. A 1995 4runner V6. I love it. The thing is that there is a rotating related clicking/clang (sounds like the wheel of fortune) that comes from the front driver side wheel. It is sometimes loud, sometimes nonexistent. I have figured out that when its in 4wheel drive. It stops...

Yeah I figured I would. . I guess its going to cost me some money for the gaskets. I think maybe a new pcv valve too while in there. Im new to the 4runner. There is so much garbage out there on the internet it seems impossible to sort through. My only other question is code 52. The knock sensor...

I searched and found a lot of info on the valve cover leaking.I have a 95 4x4. V6. I know my driver side is seeping. But the passenger side is hard to see. I know I smell a lot of oil burning on the manifold. It stinks. Bad. It leaves a small quarter size spot after a day. I just bought this...