2014-2016 behind grill light bar mounts.

[Stevee]

Paypal Sent

Thank you

 

[jmweilacher]

PayPal sent
Thanks

 

[SOOTRD]

Will this work on a TuRD Pro? I think the front grill is a little different?

 

[BradBrad619]

Will this work on a TuRD Pro? I think the front grill is a little different?

I would assume they'll work. The lower grill on the Pro looks the same as my TE. Can anybody confirm the aluminum X-cross member is the same for both models?

 

[cjacob316]

there is no difference in the vehicles what so ever

 

[4RunnerINprogress]

PayPal sent!

 

[06HAOLE]

PM sent

 

[BradBrad619]

Just shipped 5 sets out, another batch will be shipped later this week.
Emails sent with tracking info :thumb3:.

 

[tral]

Any update on if this will allow a 30" to fit in there? I have a 30" awaiting install either with these mounts (pending answer) or the redneck way.

 

[Styer]

Just shipped 5 sets out, another batch will be shipped later this week.
Emails sent with tracking info :thumb3:.
View attachment 185892

That's one pretty piece of hardware there. I have to say all that welding is top notch and looks really great. Though you could probably reduce your manufacturing costs by taking out a lot of the welding.

 

[Pkniland]

Any update on if this will allow a 30" to fit in there? I have a 30" awaiting install either with these mounts (pending answer) or the redneck way.

Where in NC are you located. I have a set that haven't been mounted yet if you want to test fit.

 

[BradBrad619]

Any update on if this will allow a 30" to fit in there? I have a 30" awaiting install either with these mounts (pending answer) or the redneck way.

30" will not fit Using these mounts.

 

[adam.friedman.33]

What is the best fitting size?

 

[BradBrad619]

That's one pretty piece of hardware there. I have to say all that welding is top notch and looks really great. Though you could probably reduce your manufacturing costs by taking out a lot of the welding.

Thanks for the kind words, much appreciated! Where would you eliminate welding? Personally i think these parts look incomplete unless fully welded. I also have high standards when it comes to welding and fabrication, quality over rules everything on my builds.

 

[BradBrad619]

Just to be clear on the figment topic. These mounts were designed for use of a 20" bar. The largest bar you can squeeze in there would be a 24", there is clearance but I have not physically installed these using anything but a 20" bar.

These mounts would also work great if you wanted to mount acouple single LED pods behind the grill.

 

[Styer]

Thanks for the kind words, much appreciated! Where would you eliminate welding? Personally i think these parts look incomplete unless fully welded. I also have high standards when it comes to welding and fabrication, quality over rules everything on my builds.

Honestly If I were building a one off bracket for myself I would do it just like you have done! Just thought I'd throw out the idea since you seemed like you were starting to produce them in number.

 

[AlrighT4R]

PM Sent with some questions. Great looking mount!

 

[raycie]

1. If you wanted to setup a couple of LED pods, would't you need 1 set per pod?

2. I was actually thinking of a heretic studios light. They are technically 11'/section, so a 20" would be a 22"... would even that be tight??

 

[tral]

Where in NC are you located. I have a set that haven't been mounted yet if you want to test fit.

Raleigh area

 

[BradBrad619]

1. If you wanted to setup a couple of LED pods, would't you need 1 set per pod?

2. I was actually thinking of a heretic studios light. They are technically 11'/section, so a 20" would be a 22"... would even that be tight??

No, 1 mount per pod. Small pods usually have a bottom mounting point with 1 single bolt hole.

A 22" bar will fit no problem.