4x Bumper with OME 880 or 881 And 906 Rear

[MTD]

Alright guys I got my 4xinnovations bumper this last weekend and I need some advice from the experts.

I anticipated that I would probably need to swap out my OME 880's for some heavier 881's, but now my concern is that the front will sit dead even or higher than the rear of the runner. I haul a boat sometimes so rake is a good thing to have.

Now here's the question will I be ok with:

1. Just keeping my 880's and 906's
2. Installing the 881's and hoping the front is at a good height with the bumper pulling it down.
3. Installing the 881's and them picking up a set of 890's for the rear.

Any feed back would be great even if it isn't along the lines of what i mentioned above. Now for the goodies:

 

[Snowy21]

I've got 882's on my rig with a tube 4xInnovations bumper and they have sagged quite a bit. Not much more lift than stock after 6 years. I just installed a winch as well so I am putting in 883's tonight. I'd think with the weight of the plate bumper you would want at a minimum 881's. I have 8 wraps in back for reference

 

[MTD]

I've got 882's on my rig with a tube 4xInnovations bumper and they have sagged quite a bit. Not much more lift than stock after 6 years. I just installed a winch as well so I am putting in 883's tonight. I'd think with the weight of the plate bumper you would want at a minimum 881's. I have 8 wraps in back for reference

So you are the one who adam built that bumper for lol. I go to UWP and initally he was going to design it off my runner when i got back to school. Guess you beat me to it though lol but any ways thanks for the advice!

 

[CenCalifoothill15]

if I were in your shoes, I'd just go with 883's. I'm running 881's with a stock bumper, I'm sure they would sag with a winch + plate bumper.

Sweet bumper btw! Looks awesome!

 

[Ol'Blue]

OH I like so much GI.....

Very nice how much?

 

[MTD]

if I were in your shoes, I'd just go with 883's. I'm running 881's with a stock bumper, I'm sure they would sag with a winch + plate bumper.

Sweet bumper btw! Looks awesome!

I would but unfortunatley I have a set of brand new 881's sitting next to me... :/

 

[MTD]

OH I like so much GI.....

Very nice how much?

They run around 670 with no hoops and the ones that I got are an extra 89 dollars I believe.

 

[Snowy21]

So you are the one who adam built that bumper for lol. I go to UWP and initally he was going to design it off my runner when i got back to school. Guess you beat me to it though lol but any ways thanks for the advice!

No problem, I kinda lucked out and was at home with family over Labor Day. I'm actually from the area. I've got a a bunch of friends at UWP and my sister is at UWW.

883's are definitely tall, I'll have measurements later today on mine. One of the nuts on the strut shaft is stuck so I'm having to head to a shop to get it taken care of. The side I did get done gained almost 2 inches from my 881's, or probably about 1.75" after it settles

 

[Bama_Runner]

Go with the 881 and if it sits dead level or just a little high in the front, add a trim packer or two in the back to level it out.

 

[MTD]

No problem, I kinda lucked out and was at home with family over Labor Day. I'm actually from the area. I've got a a bunch of friends at UWP and my sister is at UWW.

883's are definitely tall, I'll have measurements later today on mine. One of the nuts on the strut shaft is stuck so I'm having to head to a shop to get it taken care of. The side I did get done gained almost 2 inches from my 881's, or probably about 1.75" after it settles

Well If you come back to the area anytime just pm me and we could get together and go wheelin I gota couple trails out by belmont to go to. between you me and my buddy with his hoerunner we would have pretty sweet group to go with lol

 

[downpour11]

I've got 882's on my rig with a tube 4xInnovations bumper and they have sagged quite a bit. Not much more lift than stock after 6 years. I just installed a winch as well so I am putting in 883's tonight. I'd think with the weight of the plate bumper you would want at a minimum 881's. I have 8 wraps in back for reference

882's and sag with a tube bumper?! Damn! That sucks. Mine never sagged one bit, that's a stiff coil.

 

[Snowy21]

882's and sag with a tube bumper?! Damn! That sucks. Mine never sagged one bit, that's a stiff coil.

Yeah, I never realized how much they sagged till I got next to some of the guys trucks from here and realized how low I was. My 882's should have been 20mm taller than 883's but they were the same height when I pulled them out. Kinda makes sense I got the lift I did then because of the increased rate on the 883's

Well If you come back to the area anytime just pm me and we could get together and go wheelin I gota couple trails out by belmont to go to. between you me and my buddy with his hoerunner we would have pretty sweet group to go with lol

Will do!