Engine Rebuild in Process

tomtundra

tomtundra

New member
So I bit the bullet and had my engine and trans pulled to have them both rebuilt. After thinking long and hard, I decided to keep it simple (the stupid is implied) and go with a stock rebuild. No supercharger, no headers, goal here is to be as reliable and fun as the day it was born.

My rig is a 98 SR5, 3.4L, A/T, 4X, with almost 280K and I call it Woody.

That said, I am breaking the bank to go OE and replace as many of the wearable items I can. Below is a list of what's been done and purchased so far - PLEASE let me know I you think I'm missing anything!

  • Engine - complete rebuild, including new heads, sensors, oil pump, timing components
  • Transmission- rebuilt with new shift kit
  • Fuel Tank dropped and new fuel pump installed
  • New Motor Mounts
  • New A/C Lines and Power Steering Lines
  • All New Filters
  • New Radiator
  • New OE Fuel Injectors
  • Replacing All Rubber

The engine should be ready to be installed next week.

Thanks in advance for any suggestions!
 
Last edited:
Register to hide this ad
Starter contacts or a new Denso starter?
I would also try to replace the heater control valve/hoses.
Im sure you got new hoses for the engine oil cooler.
 
tomtundra said:
So I bit the bullet and had my engine and trans pulled to have them both rebuilt. After thinking long and hard, I decided to keep it simple (the stupid is implied) and go with a stock rebuild. No supercharger, no headers, goal here is to be as reliable and fun as the day it was born.

My rig is a 98 SR5, 3.4L, A/T, 4X, with almost 280K and I call it Woody.

That said, I am breaking the bank to go OE and replace as many of the wearable items I can. Below is a list of what's been done and purchased so far - PLEASE let me know I you think I'm missing anything!

  • Engine - complete rebuild, including new heads, sensors, oil pump, timing components
  • Transmission- rebuilt with new shift kit
  • Fuel Tank dropped and new fuel pump installed
  • New Motor Mounts
  • New A/C Lines and Power Steering Lines
  • All New Filters
  • New Radiator
  • New OE Fuel Injectors
  • Replacing All Rubber

The engine should be ready to be installed next week.

Thanks in advance for any suggestions!
Click to expand...

Who did you go with for a rebuild? or your doing it yourself

yota shop has a pretty good list of things they do when rebuild

they have 3 levels you can purchase, but they seem to have as close to new condition IMO but I'm sure other engine builders out there have good quality.

https://www.yotashop.com/toyota-3-4l-5vz-95-04-engine-short-block-5vz-sb-9504/
https://www.yotashop.com/toyota-3-4l-5vz-95-04-engine-long-block-5vz-lb-9504/
https://www.yotashop.com/toyota-3-4l-5vz-95-04-engine-dressed-long-block-5vz-dlb-9504/

I kind of messed up my #5 cylinder bad enough to call it quits with my motor... I ordered a dressed long block so hopefully it will be pretty decent when it arrives.

I have been working on re-doing my truck for a while now... but whenever I have to remove something I take it and get it sandblasted and powder coated before I put it back on, expensive yes but it looks like brand new and hopefully will keep the rust down. if you have the time and $ to spend do it right and re-paint if possible. just helping you spend more money. :)
 
Last edited:
sleepydad said:
Who did you go with for a rebuild? or your doing it yourself

yota shop has a pretty good list of things they do when rebuild

they have 3 levels you can purchase, but they seem to have as close to new condition IMO but I'm sure other engine builders out there have good quality.

https://www.yotashop.com/toyota-3-4l-5vz-95-04-engine-short-block-5vz-sb-9504/
https://www.yotashop.com/toyota-3-4l-5vz-95-04-engine-long-block-5vz-lb-9504/
https://www.yotashop.com/toyota-3-4l-5vz-95-04-engine-dressed-long-block-5vz-dlb-9504/

I kind of messed up my #5 cylinder bad enough to call it quits with my motor... I ordered a dressed long block so hopefully it will be pretty decent when it arrives.

I have been working on re-doing my truck for a while now... but whenever I have to remove something I take it and get it sandblasted and powder coated before I put it back on, expensive yes but it looks like brand new and hopefully will keep the rust down. if you have the time and $ to spend do it right and re-paint if possible. just helping you spend more money. :)
Click to expand...

Great info Sleepy, thank you. Based on the link I went with Level 3, including the Aisin pumps and OE timing components.

I went with a local rebuilding I know and trust. I haven't gone the powder coat route, I did have the block, oil pan and valve covers painted black and grey with high temp engine paint. Nothing too fancy, but figured I'd give it a "I"m new" look. I do like your idea of SB and coating parts!

Once the mechanical work is done and I'm happy with it (hell, I REALLY hope I am), I plan on sound proofing and new interior....and if I'm still happy, then a new coat of paint.

Thanks for your help!
 
Etool711 said:
Rear Axle seals
All bushings (Sway bars, rack and pinion, body mounts, etc)
Brakes
Brake lines
Click to expand...

Bushings - hells yes. Those need to be done!
Brakes are good, running Powerstop Friction and Vented Rotors; I went braided steel brake lines awhile back.

Thanks for chiming in!
 
BrianSD_42 said:
Do the headers. There is no risk and it's an easy upgrade

Where in SoCal?
Click to expand...

Thanks Bri. I really struggled with the question of headers. I read alot of posts, including yours (which is great), but in the end decided not to. This will be a simple daily driver. Somewhere I saw a post about these trucks not being sports cars, so why try to make them something they're not. Nothing against the HP chasers out there - lord knows I'd love a SC rig..maybe someday!

I'm in Socal, IE territory.

Thank you for your input....don't laugh at me too hard if I forgot all I wrote and mount headers anyway, I'm fickle like that. :loco::loco:
 
cps3575 said:
Nice, about how much is it going to cost?
Click to expand...

I knew this question would come up and I plan to list all my expenses at the end of the project. As for now the only thing I've actually paid for were the OE Injectors, $865 for all 6 from the local Dealer. The Machine Shop and the Mechanic are scribbling in their ledger and will let me know when it's time to settle.

Please don't think I don't care about the expense, I trust both shops I'm using, but ultimately I want it done right.

Thanks for the question!
 
You must log in or register to reply here.

Members online

No members online now.
Total: 291 (members: 0, guests: 291)

Forum statistics

Threads
278,309
Messages
3,554,068
Members
248,016
Latest member
Advally Service

Share this page

Trending content

Back
Top