• If you plan to post to Classified forums, you must follow these rules, or your post will be deleted.

    1. Thread title must include at a minimum: FS or FT, Item(1st, 2nd, 3rd, 4th or 5th gen), Price and Location. For Example: FS: 4th GEN Carpet Floor Mats - Tan, $50 Denver, CO.
    2. All Threads must contain the following information
      • What is for sale/trade (model, specs, etc.)
      • Condition
      • Price/What you want to trade for
      • Location of item
      • At least one picture of the item for sale or for trade
    3. No "Feeler" Threads - Its either for sale or it isn't.
    4. Moderators lock Classified Threads that have not had any activity in 90 days or when the part is announced SOLD.
    5. Threads not complying with the rules will be deleted without notice.

Part a 2000 LTD 4WD and 1999 4WD SR5 - Mid Atlantic (NC)

Looking for the rear hatch license plate bezel and the "gasket" piece that fits between it and the body. Pic attached as an example. Need the plastic mount points (in back of it) for the key lock cylinder to be intact.
MI 48879
cf37dbad84252ef1f0deb97d8d6f74aa.jpg


Sent from my SM-G965U1 using Tapatalk
 
i need all the mounting for the radiator. The metal vertical pieces that holds the radiator to the body, and the square nuts/bolts that those pieces bolt to on the radiator. There are 4 square nuts/bolts and also need the bolts that hold the shroud to the radiator support pieces.

Basically all bolts/nuts/mounting hardware for the radiator that can be taken off the radiator/shroud assembly

i'm in NC as well.
 
Hey man, you still have parts? If so I need a 4wd auto shifter and bezel. (SR5) I don’t need the limited one, it’s just for photo reference to what I’m talkin about.. Photo below. Thanks!!

a64e61a2f0b52491d94664b3e9b2ecae.jpg
 
Studs, Washers, Nuts

Looking for the 4 studs, washers, & nuts from the output on the transfer case. These are in the companion flange on the back of the transfer case to bolt the drive shaft to. Thank you.
 
jerbrun0515 said:
Looking for the rear hatch license plate bezel and the "gasket" piece that fits between it and the body. Pic attached as an example. Need the plastic mount points (in back of it) for the key lock cylinder to be intact.
MI 48879
cf37dbad84252ef1f0deb97d8d6f74aa.jpg


Sent from my SM-G965U1 using Tapatalk
Click to expand...
Hello,

I'm sorry for the very delayed response. I actually wasn't getting notifications for a while and this totally skipped my mind. Are you still looking? I can check to see if I have a good one if you are. Thanks!

Sent from my SM-G930V using Tapatalk
 
RPTFE00 said:
Hey man, you still have parts? If so I need a 4wd auto shifter and bezel. (SR5) I don’t need the limited one, it’s just for photo reference to what I’m talkin about.. Photo below. Thanks!!

a64e61a2f0b52491d94664b3e9b2ecae.jpg
Click to expand...
I'm sorry for not replying sooner. I do have them if you are still interested. Take care.

Sent from my SM-G930V using Tapatalk
 
billmilner said:
Looking for the 4 studs, washers, & nuts from the output on the transfer case. These are in the companion flange on the back of the transfer case to bolt the drive shaft to. Thank you.
Click to expand...
Are you still looking? Sorry for the delayed response.

Sent from my SM-G930V using Tapatalk
 
Hey, I am just a few miles from you in NC.

Have any A04A 4.30 elocker setups? front diff clamshell and full rear axle
 
You must log in or register to reply here.

Members online

No members online now.
Total: 3,313 (members: 0, guests: 3,313)

Forum statistics

Threads
278,316
Messages
3,554,121
Members
248,016
Latest member
Advally Service

Share this page

Trending content

Back
Top