Rear Recovery Point Sale $90 per pair - Kansas

[patkelly4370]

Installed the recovery points today. Had to trim the SR5 exhaust as it runs along the frame blocking the bolt holes.
I would have mounted the in the other holes, moving them rearward a bit, but I didn't because of the frame welds.

Sent from my SM-G955U using Tapatalk

 

[DannyLlama]

What kind of paint is recommend to coat these with before install.. I'm wanting to paint them blue if that's any indication to waht kind of paint.

 

[patkelly4370]

What kind of paint is recommend to coat these with before install.. I'm wanting to paint them blue if that's any indication to waht kind of paint.

I used industrial paint (rattle can) for farm/industrial equipment from Tractor Supply.
Ambient temperatures over 100° every day, it took a week to cure.

Sent from my SM-G955U using Tapatalk

 

[Inv4drZm]

What kind of paint is recommend to coat these with before install.. I'm wanting to paint them blue if that's any indication to waht kind of paint.

I would use just a cheap rattlecan myself, they can sometimes scrape the bottom side coming down ledges so it would be an easy touch-up.

Basic Rustoleum Satin Black is what I use on my bumpers and sliders. Satin or matte I think looks best for undercarriage stuff, not sure if that can be found in a blue.

 

[DannyLlama]

Thanks!

Is there a recommended torque LBS that the bolts should be torqued to?

 

[Inv4drZm]

Thanks!

Is there a recommended torque LBS that the bolts should be torqued to?

M12-1.25 should be around 70 ft-lbs.

 

[gigajoe]

Interested in a pair.

thanks

 

[Bernardchan96]

Let me know when next batch is available. im interested

 

[Inv4drZm]

Sold out for now. I'll let you know when we're doing another batch.

Thanks everybody!

:thanks:

 

[arehman11]

Sold out for now. I'll let you know when we're doing another batch.

Thanks everybody!

:thanks:

Are you in Kansas City by chance chance? I swear I remember a very similar username on a local forum.

 

[Inv4drZm]

Are you in Kansas City by chance chance? I swear I remember a very similar username on a local forum.

Salina

 

[Wingman707]

Im ready for a pair

Nice little project! I am ready for a pair. I have subscribed to this page. Let's Go! Have a good new year.

 

[Daemoro]

I'm subbed and waiting for the next group. Finally getting to work on my 4R!

 

[cwilliams563]

I would like to get in on the next buy for my 4th gen.
Subscribed.

 

[vdog2000002]

I would like a set for a 5th gen.

 

[Inv4drZm]

[MENTION=100551]Wingman707[/MENTION] [MENTION=72648]Daemoro[/MENTION] [MENTION=511893]cwilliams563[/MENTION] [MENTION=592167]vdog2000002[/MENTION]

And everyone else.

We might be starting another batch soon.

Anyone else interested?

 

[dcguy]

[MENTION=100551]Wingman707[/MENTION] [MENTION=72648]Daemoro[/MENTION] [MENTION=511893]cwilliams563[/MENTION] [MENTION=592167]vdog2000002[/MENTION]

And everyone else.

We might be starting another batch soon.

Anyone else interested?

I am interested

 

[patkelly4370]

I have yet to use mine, but I'm glad they're there.
I did a tough (for newbie me) run with a local club that was all Jeeps. They were curious and impressed with them.

Sent from my SM-G955U using Tapatalk

 

[NB17Limited]

[MENTION=100551]Wingman707[/MENTION] [MENTION=72648]Daemoro[/MENTION] [MENTION=511893]cwilliams563[/MENTION] [MENTION=592167]vdog2000002[/MENTION]

And everyone else.

We might be starting another batch soon.

Anyone else interested?

I'd buy them

 

[scottiezilla]

Been watching this for awhile
Interested
Curious about the unused 3rd hole in patkelly4370s pic? Additional support if we decide to drill frame?
How difficult/what’s required in rerouting exhaust?
Wouldn’t want to cut exhaust if not necessary or would like to know more about the effects of cutting if need be
Excited these back
Thanks again everyone