What did you do to/in your 5th Gen today?!
- Thread starter DEKA3
- Start date
Hillbilly Mac
New member
Reverse rake like whoa! What are those coilovers set at...like 5" lift? I hope you get your spanner wrenches ASAP for your sake
ToyTec set at 2.5", they're somewhere around 2 right now. It's a bit of an optical illusion with my driveway too. Everything should be fixed tomorrow.
J-BlickPhoto
New member
nevans2005
New member
Add using the sliding rear tray as a changing table to the list
Don't forget the diaper in the hatch...done that before, and never will again
FactoryRide
New member
How far east?
J-BlickPhoto
New member
Most likely Georgia. I'm meeting a friend of mine.
FactoryRide
New member
Well if you end up in North Ga, holler at me.
I'm in Marietta and Cumming all the time.
and some local guys are planning on going up to Tray mtn to ride on the 30th if you're here then. Then Saturday we'll be up at bull mtn.
It would be sweet to see your rig in person!
I'm in Marietta and Cumming all the time.
and some local guys are planning on going up to Tray mtn to ride on the 30th if you're here then. Then Saturday we'll be up at bull mtn.
It would be sweet to see your rig in person!
AZrunner11
New member
Made some room for my 285s
I did the front fender mod tonight and removed the mud flaps to make some necessary room for my 285 MT/Rs.
I did the front fender mod tonight and removed the mud flaps to make some necessary room for my 285 MT/Rs.
sandcrawler
Senior Member
looks good. what paint(s) did you use?
nguyenn
New member
Dealer installed the factory cross bars for the roof rack that I ordered at the time of purchase two weeks ago.
Came home and installed one of my Rocky Mounts carriers and my fat bike adapter.
Had to move the front bar all the way forward to so the bike tray didn't hit the open hatch. This meant pulling out the 3" long rubber spacers they had in the side bars. Noise doesn't seem to bad so far but the Rocky Mounts are very low profile.
Came home and installed one of my Rocky Mounts carriers and my fat bike adapter.
Had to move the front bar all the way forward to so the bike tray didn't hit the open hatch. This meant pulling out the 3" long rubber spacers they had in the side bars. Noise doesn't seem to bad so far but the Rocky Mounts are very low profile.
Hillbilly Mac
New member
Got it leveled with some good ol' fashioned Hillbilly Engineering...& it IS (finally) actually level now. My driveway on the other hand...
fishstick21
New member
CB install
Finished installing the Cobra 75. I ran the wiring from the mount on the Yakima rack through the Shark Fin into the cab. No more XM but I never used it anyway.
Finished installing the Cobra 75. I ran the wiring from the mount on the Yakima rack through the Shark Fin into the cab. No more XM but I never used it anyway.
NikitaVelour
Member
Added some rumble!
After doing some searching around here and listening to sound clips I ordered a Magnaflow 12256 and had it installed along with a shiny new exhaust tip! I am so happy with the sound! Now she purrs and growls! Thank you to c2one for your help!
Just a few tip pics lol
After doing some searching around here and listening to sound clips I ordered a Magnaflow 12256 and had it installed along with a shiny new exhaust tip! I am so happy with the sound! Now she purrs and growls! Thank you to c2one for your help!
Just a few tip pics lol
Looks good! Real clean. I'm glad you like it and the install went smoothly.
OldSchool1959
New member
Cooper A/TP 275/55/20s on stock wheels added today. IMO, a much better stance. Actual license plate depicted in photo. Truck and household protected by Colt and FNP.
FactoryRide
New member
Finally got around to extending the rear diff breather thanks to a couple of threads on here. Didn't think to take any pictures since it is already well documented.
jbstrd
New member
Did you just go into the jack storage compartment or did you go into the fuel filler door?
Similar threads
