What Did You Do To Your 3rd Gen Today?

Status
Not open for further replies.
finally spent the money on much need parts.$400+ for lbj's,ite's and ote's..bummed because i already did that on the old truck and this christmas bonus money could have been sliders.... =-(


i suppose it's better than a wheel falling off though...i just hate doing the same work twice....

Good time to inspect play from your front wheel bearings so you don't end up taking it all apart again.
 
ARKRWl58525 said:
Good time to inspect play from your front wheel bearings so you don't end up taking it all apart again.

After this , christmas,my wifes birthday,new years and a road trip to vegas ...im already eating dirt for the next month to stay alive , may just have to do the work twice , haha , such is life....i also have a cb install, new battery solenoid and lights to wire up....I'm going to be a busy boy for the next week !
 
^^^^


Wow looks amazing from what we can see. More pics are needed







looks like mine when I first got it, lol

Thanks guys! Here's another
7uquveqy.jpg
 
After this , christmas,my wifes birthday,new years and a road trip to vegas ...im already eating dirt for the next month to stay alive , may just have to do the work twice , haha , such is life....i also have a cb install, new battery solenoid and lights to wire up....I'm going to be a busy boy for the next week !

What CB did you get and with what antenna are you matching it with?
 
Sat in it on the side of the freeway because I ran out of gas 2 miles from the gas station. Strangely I put about 2.5 gallons in and went to the gas station and it only took 14.5 gallons. Where did the other 1.5 go?

Later though I drove my daughter downtown for a daddy daughter date. Got to love eating schwarma's, ice cream and checking out a train exhibit with your two year old.
 
There's about a gallon that the fuel pump can't reach because of its location and I think a low spot in the tank. Stupid yes...but they can advertise it as an 18 gallon capacity instead of 17.
 
Changed the oil (Royal Purple 5w30) & filter, rotate and rebalanced my tires, and flushed my coolant system - got bored at work, lol
 

Attachments

  • WP_000403.jpg
    WP_000403.jpg
    63.9 KB · Views: 708
Last edited:
today I changed the climate control #74 bulb (and green bulb condom) and constructed my heavy duty shielded ground wires for the Big 3 upgrade tomorrow
 
Towed something for the first time ever and it was in my 4runner.

Moved into my new office today and used a 5x9 uhaul trailer.

Went as expected. Looking forward to buying my own trailer in the near future.
 

Beautiful! First time I've seen those 17's on a 3rd gen I love it.

There's about a gallon that the fuel pump can't reach because of its location and I think a low spot in the tank. Stupid yes...but they can advertise it as an 18 gallon capacity instead of 17.

I've been under the impression my tank is 16.5 gal in my 96. Did they make it bigger 99+? Or am I just completely wrong altogether... I've had it wayyy below E and when I pulled into the gas station and filled up it topped off at 16.2... or does your comment still answer my question lol
 
Thermostat 180*

Wasn't sure until I drove it around, but after replacing probably a perfectly good thermostat, I realized that, in doing so, my interior heat has not increased beyond a chilly 60-ish degrees no matter how far or fast I drove my 'Runner around. Frowns.

I really don't want to crack open the heater element for the passenger compartment. Maybe I can use a solvent to break down the particles in the cooling system because there is some. I don't know where it is coming from.

Anybody know what I should use to flush the radiator or maybe replace the radiator altogether?
 
Changed out both front axles. Boots started to leak after my lift. Never tore, just leak and the bands were very loose. Getting ready to test drive it now. Quite a bit of beating on the pry bar to get the old ones out, but new ones went in very easy.

Noticed my next upgrade will be new heavy duty front swaybar end links. Mine are bent and bushing are shot.
 
I'm currently finishing my late-night project. Painting my corner lights after I saw that the tinting film I put on was peeling. Made my corners look like the JDM corners :D

Crappy night pic from my iPhone. Will get a better one tomorrow.

IMG_26651.jpg~original
 
Last edited:
Status
Not open for further replies.

Members online

No members online now.

Forum statistics

Threads
278,316
Messages
3,554,120
Members
248,016
Latest member
Advally Service

Trending content

Back
Top