What Did You Do To Your 3rd Gen Today?

[BasinRunner]

[/URL]~original[/IMG]

Picked these up for $250 (need rebuild). Sending them out Monday.

 

[montana_jeepn]

Changed fuel filter.
Installed Revtech front diff drop.
Checked transfer case fluid....was going to hinge the fluid but it was full and still clear.
Realized I didn't have the correct tools for the front diff.

 

[BenK]

Steering rack guide replacement. Fixed a rattle I've been chasing. Well worth the $65 and 30 minutes. :cheers:

 

[Supra725]

Rob,

you think that's bad.. try Davis Cyclist.. they don't look both ways and runs the stops signs.. on top of that, the Prius drivers in Davis are horrible..

One night when I went out, some nutjob with an Prius decided to take both the parking spots in their little car and leaving the rest of the people to scramble for spots in our rigs..

 

[RunninInGA]

Swapped the blown stock rear speakers with.......stock speakers I got from another member long ago.

Also started on this.

 

[Jaketino]

What did you do to your 3rd gen today?

Did a complete transmission flush and installed my transmission cooler (not currently working but installed). Need some more trans hose to finish the job. Got the cooler in without taking the grill off which seemed like a huge win to me.

 

[TXRick]

Started to replace my knock sensors. Will finish this week.

 

[Cow_doc.308]

Between calls and other obligations, I got my new whip antenna installed, picked up a set of LC coils, pulled most of my trim off and painted it, and gave her a much overdue bath.

Now I've just gotta get the trim replaced and paint a few pieces that I didn't remove.

 

[shadyluke]

Got her cleaned up. Still need to remove the running boards.

 

[Skidmarcx]

What did you do to your 3rd gen today?

Flexed it out on Desoto Mine!

 

[T4Ryota4life]

longer sway bar end links

I added longer rear sway bar end links from a 94-95 4Runner to help with some unwanted rear sway. I have toytec superflex rear springs, extended travel Bilstein shocks and Sonoran steel adjustable pan hard bar. These end links bolt right up and have solved my problem.

 

[42s on u]

Got my roll bar and tool box in.

 

[42s on u]

One more shot

 

[Dmart_808]

after getting another ticket for having no mudflaps,
and too cheap to buy the real deal,
i made some wanna be joas flaparoonies!!

(( i think somthing is wrong with my camera phone lol...)

 

[TakeitApart]

Took a drive up a tower access road that I haven't been to before.

 

[shadyluke]

Got my roll bar and tool box in.

That would be pretty sweet for secure gun storage. I bet an AR would fit right in there along with some other goodies.

 

[KSWAY]

Got my roll bar and tool box in.

What are you doing to keep the tools from rattling around? I was gona do a similar set up. But the rattling would drive me nuts.

 

[jmildoc]

Used my dual action polisher finally.

Used compound then polish then wax. All in about an hour and a half. Will do a more thorough job at a later date.

 

[mtvp]

Got her cleaned up. Still need to remove the running boards.

I for one like running boards. They keep the snow, salt, and mud at bay from the sides. The little people like them as well. Not all 4 Runners are rock crawlers / lifted rigs yet.

 

[shadyluke]

I for one like running boards. They keep the snow, salt, and mud at bay from the sides. The little people like them as well. Not all 4 Runners are rock crawlers / lifted rigs yet.

At stock height i think they are in the way. I feel like i have to step out too far cuz they are awkward at this height. My crawler is in the garage, this is just a beater.