What Did You Do To Your 3rd Gen Today?

[MTD]

Mmmmm tacos.

Yep lol

 

[Asaspades93]

sliders on and primed, few more coats and paint coming tomorrow. also did an oil change

 

[JBurt]

Went mountain biking today and had a little whoopsie lol met a new 4runner friend though lol

It'll buff out. Any damage to the rider?

 

[xcmtb83]

Went mountain biking today and had a little whoopsie lol met a new 4runner friend though lol

You crash can be attributed to not removing your reflectors upon purchase.

 

[MTD]

It'll buff out. Any damage to the rider?

No major damage to the rider lol mainly his pride lol

You crash can be attributed to not removing your reflectors upon purchase.

Well of course!

 

[brkosk]

Installed some Cree LED lights!

Not bad for $38 on amazon with prime shipping. Rated at 1600 lumens each. Hopefully they last a while. I'm thinking of adding some black silicone around the edges to seal it up better.

I was so impressed by the output I had to order up a 20" bar for the top of the bumper!

 

[Deezil]

bypassed the radiator for an external trans cooler, and a trans temp guage, added two more always powered cig lighter plug ins for powering stuff, tinted the windows myself, painted the wheels, adding airshocks in the next couple days to the rear. Been busy!

 

[kingin]

Installed new tires and installed new clutch kit and new flywheel. Should have paid a shop to do the clutch too much work lol

 

[Deezil]

^^ I almost painted my wheels black, wife said I should have, haha.... :/

 

[brkosk]

bypassed the radiator for an external trans cooler, and a trans temp guage, added two more always powered cig lighter plug ins for powering stuff, tinted the windows myself, painted the wheels, adding airshocks in the next couple days to the rear. Been busy!

How did the tinting go? I've done it once before and it always looked DIY.

 

[Deezil]

How did the tinting go? I've done it once before and it always looked DIY.

3rd rig Ive done, Ive got it figured out pretty well now, precut tint for windows on ebay for $13, took me one hour to do both front windows on the 4runner. There was a little learning curve, but I think it looks great! And I saved over $100 and half a days wasted time. Last two rigs I paid to have done, they left the door panels soaked and pockets full of water solution.. and this was from the best place around. :/

 

[jmildoc]

Installed some Cree LED lights!

Not bad for $38 on amazon with prime shipping. Rated at 1600 lumens each. Hopefully they last a while. I'm thinking of adding some black silicone around the edges to seal it up better.



I was so impressed by the output I had to order up a 20" bar for the top of the bumper!

Which ones were these? The 6led ones? I have those in my wish list. Lol. Waiting for my current ones to go out

 

[brkosk]

Which ones were these? The 6led ones? I have those in my wish list. Lol. Waiting for my current ones to go out

Yes, 6 LED. I still can't figure out how to wire them tapping into the stock headlight switch.

I can manually switch them on and off at the relay under the hood but the instructions I found looked to be for models with DRL. I was missing a wire in the C13 connector in the steering column.

 

[artemgzn]

CV Boots got replaced and the rear shock got re-installed properly. No more rattling on every bump :dance:

 

[MileHighClimb]

Finally built some drawers after 6 months of having materials!!

 

[GVL]

Finally built some drawers after 6 months of having materials!!

Very nice, I'll be doing something similar soon, but need to keep it dog-friendly back there so mine will be much lower - just enough room for winching accessories and some survival basics. What kind of covering did you use? I'm still debating that part - needs to be fairly rugged since I haul a lot of firewood.

 

[TOYOTA_YV]

[/ATTACH] I got a set IROK ND's mounted ( 235/85R16 ). And ordered part of my lift.

How are they in highway?...

 

[MasonT4R]

Finished wiring up my Aux Reverse Light and License Plate Light (yay I'm legal again!)

 

[MileHighClimb]

Very nice, I'll be doing something similar soon, but need to keep it dog-friendly back there so mine will be much lower - just enough room for winching accessories and some survival basics. What kind of covering did you use? I'm still debating that part - needs to be fairly rugged since I haul a lot of firewood.

I just used thin carpet that i found at my Lowes. Its pretty think and rough and does the job well.

 

[MileHighClimb]

Started and finished my satoshi mod.

I also gave her a wash and wax with some black enhancing wax stuff.