What did you do with your 4runner today?

[97BlackAckCL]

Well I started installing my light bar on my bumper, got through tapping the first 2 holes and my drill died. Time to wait 4 more hours.

backup battery ftw

 

[HHIRunner]

backup battery ftw

Blown through both

 

[hearno]

SO MUCH WIN IT DESERVES ITS OWN THREAD!!!!!!!!!!!!

but here's a pic:

Level 8 MK6 in 17x8 -10 with KM2 255/80 17s

 

[Buckles]

New plates

 

[HHIRunner]

Finally got it done. This sucker is bright

 

[montijo505]

SO MUCH WIN IT DESERVES ITS OWN THREAD!!!!!!!!!!!!

but here's a pic:

Level 8 MK6 in 17x8 -10 with KM2 255/80 17s

Not a big fan of the bronze. But you, sir, pulled it off!

 

[llennium]

Finally finished the winch install and added some under hood lights while I was in there.

 

[Slowgoat]

Finished the audio install on the new to me 4runner.

Put in a kenwood XR900-5.

Holy crap!

Sounds great!

Thanks gshadow325! !

 

[Bthbama]

I used a drimmell tool to shorten the length on rear mud flaps. This avoided that huge rear wheel well hole...and allowed more visual of the more aggressive treads. Mud flaps hide nice tires.

 

[morphious]

I used a drimmell tool to shorten the length on rear mud flaps. This avoided that huge rear wheel well hole...and allowed more visual of the more aggressive treads. Mud flaps hide nice tires.

:worthless

 

[Rocket61]

I used a drimmell tool to shorten the length on rear mud flaps. This avoided that huge rear wheel well hole...and allowed more visual of the more aggressive treads. Mud flaps hide nice tires.

Good call. I trimmed mine right down to the line of the bumper. Kept the piece in the wheel well to avoid the huge hole you described. Looks way better in my opinion. Did that same with the fronts.

 

[Bthbama]

Good call. I trimmed mine right down to the line of the bumper. Kept the piece in the wheel well to avoid the huge hole you described. Looks way better in my opinion. Did that same with the fronts.

That's essentially what I did. I cut them almost flush and used a grindstone to give it a nice edge . Not factory molded but I can live with that over the hole
I'll try to post a pic.

 

[Tayzorz]

SO MUCH WIN IT DESERVES ITS OWN THREAD!!!!!!!!!!!!

but here's a pic:

Level 8 MK6 in 17x8 -10 with KM2 255/80 17s

Nice wheels!!!




Today I did this

 

[Cygan1008]

Changed the oil/filter and installed my diy fender liners
Before

After

 

[jsmith21]

Changed the oil/filter and installed my diy fender liners
Before

After

What'd you use? Those look great. Mine are cracked in about 26 different places and barely hanging on.

 

[Greydog]

Finally finished the winch install and added some under hood lights while I was in there.

Hi, can you comment on what kind of lights you installed? Was it an LED strip light?

Thanks.

 

[Greydog]

1. Installed the rear diff breather extension line mod up to the gas cap locale.

2. New clamp on PS inboard CV boot, used a 1.5-2.0" clamp, just fit with some pressure.

3. Broke my 30" breaker bar on the damn DS axle nut, no luck with the DeWalt impact wrench either. Likely the shop used an impact to torque the nut, its F-in on there... Time for a shop to crack it loose...

4. Called Bud Built, sliders may ship next Friday, betting its the week after, sounds like their free shipping celebration was a success....

 

[Bthbama]

That's essentially what I did. I cut them almost flush and used a grindstone to give it a nice edge . Not factory molded but I can live with that over the hole
I'll try to post a pic.

Pic of mud flap length reduction with the drimmell tool.

 

[Cygan1008]

What'd you use? Those look great. Mine are cracked in about 26 different places and barely hanging on.

1/8" oil resistant rubber from mcmasters.com, if I was doing it again I would go with 1/16" instead.

 

[Net4n6]

1/8" oil resistant rubber from mcmasters.com, if I was doing it again I would go with 1/16" instead.

I went to website mcmasters.com. It is not working. What/Where did you use for the template? Mine is totally ripped.