gshadow325
New member
Compustar dash dual HD dash camera system. Awesome system
What did you do with your 4runner today?
- Thread starter NorthGa4R
- Start date
awdjunkies
New member
Fixed it for you at no additional cost :biggrin1:
CookieRoe
Senior Member
Fix Or Repair Daily
Brutalguyracing
New member
emelianenkov
New member
Hit a few trails with [MENTION=79603]Chill will[/MENTION] this afternoon. Had a good time!
MarkinWMich
New member
Coolant flush and fill.
Always looking for some excuse to tinker with the toy.
Always looking for some excuse to tinker with the toy.
Captain Texas
New member
[MENTION=100305]TiN[/MENTION] just curious, what is the diameter of your RS-720 mount? I've gotten two both 3/4" diameters and I think that's my problem.
zopperman
Moderator
Where are you ordering from?
Captain Texas
New member
Vendor from eBay.
TiN
New member
This is the mount I purchased: Comet RS-720 - Medium Duty Ham Radio Antenna Lip Mount
5/8" hole as confirmed by digital calipers.
The stud I am using says it is designed for 1/2 inch holes, but still works because the retention nut is larger than 5/8".
kevinpt
Senior Member
was looking at how im going to mount my offroad lights and a friend said i could put them where the fogs are. not going to be replacing my fogs with them but here is what they would look like behind the trim. dont know how they would be mounted but here you go
going to be getting a kc hitch mount and mount them in my cbi front hidden hitch
going to be getting a kc hitch mount and mount them in my cbi front hidden hitch
Captain Texas
New member
montana_jeepn
New member
New LCA's
Replaced my LCA's with new factory LCA's. My cams were frozen so the alignment shop didn't have much to work with. With 134k on the odometer I figured it wouldn't hurt to replace the balljoints.
The two rear cams came out pretty easy, but the two fronts I had to cut out with a Sawzall. What a pain in the butt that was. The whole project took me about 8hrs, but that included a run to HomeDepot for cutting blades and waiting for the paint to dry after I touched up the scratches from the saw blade on the frame with chassis paint. I also painted the LBJ brackets that bolt to the bottom of the knuckles since I had them off.
My advice to anyone doing this is to have all cams/bolts in hand prior to starting and assume you will have to cut them out......if not, consider yourself very lucky and just return the parts that you don't use.
I found this guide to be very helpful front LCA removal & bushing replacement - Toyota 120 Platforms Forum
My next big project will be rotors, pads, and calipers all the way around.
Replaced my LCA's with new factory LCA's. My cams were frozen so the alignment shop didn't have much to work with. With 134k on the odometer I figured it wouldn't hurt to replace the balljoints.
The two rear cams came out pretty easy, but the two fronts I had to cut out with a Sawzall. What a pain in the butt that was. The whole project took me about 8hrs, but that included a run to HomeDepot for cutting blades and waiting for the paint to dry after I touched up the scratches from the saw blade on the frame with chassis paint. I also painted the LBJ brackets that bolt to the bottom of the knuckles since I had them off.
My advice to anyone doing this is to have all cams/bolts in hand prior to starting and assume you will have to cut them out......if not, consider yourself very lucky and just return the parts that you don't use.
I found this guide to be very helpful front LCA removal & bushing replacement - Toyota 120 Platforms Forum
My next big project will be rotors, pads, and calipers all the way around.
Slowgoat
New member
Found On Road Deserted
Jeffrey_VB
New member
Driving mine back home to Asheville in about a week and a half.
AZ07Runner
Member
Went out into the desert to do some shooting with friends. Guns we brought: M&P Pro 9mm, AR15, 12 gauge, 20 gauge, Ruger 10/22 i-TAC, Sig 2022, Rossi .357 revolver, and a Browning .22 lever action.
A lot of lead flew today!:AK47::gun6:
A lot of lead flew today!:AK47::gun6:
kevinpt
Senior Member
OVERLAND IN TX
New member
Similar threads
