kingofthehill
New member
That is cool!
What did you do with your 4runner today?
- Thread starter NorthGa4R
- Start date
That is cool!
momo.75
Registered User
Replaced one of my worn out keyfobs with one from ajtdesign-llc.com
It is plastic but it looks and feels quite nice. Swapped internals from older fob into new one (takes at most 5 mins). Very happy with it and will probably swap out my second key fob too.
Sent from my Pixel 2 using Tapatalk
I got one of these as well. Actually I got a red and black. I will switch out the fronts and backs from time to time. He did a great job on them
hgill
Member
I really wanted to get the red one, but thought maybe my old buttons would look off combined with a bright red so played it safe with black. Im thinking I will probably get a red and black one next to replace the other key fob (need to tell the wife the other one is broken too) :bounce:
kingofthehill
New member
I ordered one last night after seeing the post. I ordered in quicksand with black screws. You can find them selling on ebay. I bought my through the ebay store.
ZebRuaj
New member
Lifted the front end to chase a hum I've been noticing for about 3 weeks. Pretty sure it was a bad wheel bearing, though it sounds a lot different than my G35 wheel bearing gone bad. Confirmed driver front is bad.
Decided to spin the passenger side just to compare. Wouldn't ya know, it wouldn't move. Seized caliper phenomenon has caught up to my rig. Bottom inside piston wouldn't budge. StopTech pads and rotor still look good, so it must've just happened.
Replaced the caliper with an AutoZone reman so I can get to work. Painted it too before install.
Ordered a Koyo + Dorman wheel and hub bearing assembly here. Guaranteed shipping by next Saturday.
160k and some demon's are starting to exercise themselves. I know what I'm doing next weekend.
Decided to spin the passenger side just to compare. Wouldn't ya know, it wouldn't move. Seized caliper phenomenon has caught up to my rig. Bottom inside piston wouldn't budge. StopTech pads and rotor still look good, so it must've just happened.
Replaced the caliper with an AutoZone reman so I can get to work. Painted it too before install.
Ordered a Koyo + Dorman wheel and hub bearing assembly here. Guaranteed shipping by next Saturday.
160k and some demon's are starting to exercise themselves. I know what I'm doing next weekend.
jsmith21
New member
Played with some led’s I had laying around. I originally bought them last year but got frustrated while installing a few of them so I just didn’t mess with them for a while. Anyways, I got bored and decided to start messing with them again and this was the end result. I need to do the 12 volt mod for the screen, and decide if I like white or blue for the screen. And then get the gauge cluster done too.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Changed oil. Also messed with transfer case actuator. Seems I lost my 2nd actuator. Only 2 years old. Of course out of warranty too. Diff lock works, and it actually goes into 4Lo, but the actuator does not sense it's in 4lo so the light keeps flashing. I can drive around in 4lo and all works perfectly. I would leave it, but my OCD won't let that happen. Spent $1200 on the OEM Toyota last time. This time ordered an Aisin for $550. I'm all for OEM, but for 2 years I can't say that's a better part, and I suspect Aisin makes the part for Toyota anyway.
On a more positive note, my Smittybuilt X20 winch showed up! Just need my Demello bumper to come now. Was told mid January but the suspense is killin!
On a more positive note, my Smittybuilt X20 winch showed up! Just need my Demello bumper to come now. Was told mid January but the suspense is killin!
riceandpho
Elite Member
some more stuff added to the dash, been eyeing this for 2 weeks, have a scangauge do some other reading
Last edited:
HCWatson997
New member
Snow and stuff
Is that a homemade rear bumper and tire carrier? I like the looks of it!
exodus_adam
New member
mounted LT265/70R17 BFG k02's on FJ wheels
installed 2.5/1.5 poly lift kit
installed 2.5/1.5 poly lift kit
NinjaOne
New member
Kinda, yeah. Local fab guy made it for me. Wanted something light-weight/high-clearance that offered some protection if needed. Didn't like how most of the plate bumpers blended (or didn't) with the body. Goal was to make the cleanest bumper around
HCWatson997
New member
How much did it cost you for everything including materials and labor?
NinjaOne
New member
I'm not supposed to say :spy:
That said, he should be wrapping up the plans to sell them starting in Feb.
Unrelated, but do you have an audio clip of your exhaust?
HCWatson997
New member
I had one on my phone but it killed itself a few weeks ago so you just gave me an excuse to go play around for five minutes:bounce:
How do you post a video clip? I tried attaching it and it said "file invalid"
NinjaOne
New member
Dropbox link, google drive link or youtube link.
HCWatson997
New member
Sorry if its kinda crappy quality btw. That last bit it just gunning it in a parking lot but only got up to about 30. Hopefully this works. I think I had it bought and installed for a total of about $240 if I'm not mistaken. That includes cutting out the resonator and replacing that piping as well
https://drive.google.com/open?id=0B3qleNeRjFd_SHJlVnQ5QjhvYm5fT2YxWmdfNENrN1pvajVz
HCWatson997
New member
If you don't mind, how do you create a build thread? I don't see any button to click to even create a new thread in general
Anonymous4Runner
New member
There are many ways to begin a build thread that can be accessed via different platforms such as Google Drive, etc. However some members prefer to see the build and text on the same page so you might be better off doing it the old fashioned way.
https://gyazo.com/21d381d57bcf3e2c42aafb9bb707dcbc
This is where you would want to click to make a new build thread and stick with it. It is right underneath T4R banner
Similar threads
