Running boad: one of the best

[ron in sc]

Just installed ATS Design running board made specifically for 4runner. Here's what make is very nice.

-made in usa
-made of extruded aluminium
-end caps can be replaced if damaged
-chome plated strip can be replaced if damaged
-brackets fit perfectly over stock brackes for lower trim panel
-Brackets are wrinkle power coated.
-excellent directions, but so easy to install they are barely needed
-packaged very well so no shipping damage
-perfect fit with or without mudflaps

 

[FatDave]

Just installed ATS Design running board made specifically for 4runner. Here's what make is very nice.

-made in usa
-made of extruded aluminium
-end caps can be replaced if damaged
-chome plated strip can be replaced if damaged
-brackets fit perfectly over stock brackes for lower trim panel
-Brackets are wrinkle power coated.
-excellent directions, but so easy to install they are barely needed
-packaged very well so no shipping damage
-perfect fit with or without mudflaps

More pictures, please.

Nice garage! Yours?

 

[ron in sc]

Here are a few more photos. I'll try to take some better ones outside later today.

And yes the garage is mine so thank you for compliment.

 

[1engineer]

Nice boards and garage!

 

[Bay33saw]

You have a toilet, sink AND a lift in your garage, please tell me where you live so I can move next door.....

Oh and more pictures of the boards would be super, I was looking at the DeeZee ones but after all the shipping problems people are having I may go another route.
Where did you get them from?

Oh and did I say you have a fantastic garage...:cheers:

Also what series running boards did you get?

 

[philsey]

...... and I'll bet there's a refrigerator too.

..... and a heater.

 

[Bay33saw]

...... and I'll bet there's a refrigerator too.

..... and a heater.

and a tire machine and a big air compressor and a pool table with a stripper pole next to it.

 

[ron in sc]

The boards are the Matrix series and the model I have is specific to the 4 runner.

As to the the garage it has 200 amp service, heated and A/C, bathroom with shower, utility sink, 2 stage Saylor Beall compressor located in another garage and paintquality air piped in to nice garage, washer and dryer, large flat screen tv and other stuff too.

Steve of the Ultimate Garage helped me with design.

Ediited: no room for tire changer.

 

[Bay33saw]

The boards are the Matrix series and the model I have is specific to the 4 runner.

As to the the garage it has 200 amp service, heated and A/C, bathroom with shower, utility sink, 2 stage Saylor Beall compressor located in another garage and paintquality air piped in to nice garage, washer and dryer, large flat screen tv and other stuff too.

Steve of the Ultimate Garage helped me with design.

Ediited: no room for tire changer.

I think you need to fix that and make room for a tire changer....LOL

DId you buy the boards from autoanything or someplace else?

 

[ron in sc]

Not to good at taking photos, note that part of board you steo is 5 1/4" measured from inside to edge where chrome strip on outiside of board starts.

 

[Stifler]

the cool factor of those running boards has been overshadowed by your garage...

 

[jspagna1]

Those running boards look nice. Look like factory. Graet job. And yes a lift in my garage would aleviate my car storage problems.

 

[philsey]

the cool factor of those running boards has been overshadowed by your garage...

Yeah, even Antman doesn't have a lift.

 

[Stifler]

Yeah, even Antman doesn't have a lift.

What kind of Jerk doesnt have a lift? lol j/k

 

[Lolrax]

These don't look much bigger than stock though, are they easier to get on to than the ones that come with the Limited? Because they are just too small.

 

[Dongbeiren]

looks kinda like the stock.

 

[MikeBuzzsaw]

I demand more pics of the garage!

 

[clemson4rnr]

What specific models of ATS Running Board are these and where did you purchase them? I am looking at getting some for the lady and the factory ones are just too damn $$$

 

[BillsRunner]

4th gen stopped to spray, not so on the 5th

So, my 4th gen factory running boards had a piece that covered the inside of the running board and stopped the spray and slush from coming up. The 5th gen (for the Premium) don't and the spray and slush come up and land right on top of the running board. I'm going to see about adding an inside strip of aluminum but wondered if anyone had a fix or a better running board for this problem?

And, yes, you get just half of a foot "purchase" on factory running board. Maybe for the 6th gen, they should just issue a retro 4th?

 

[4r-4ever]

i think the garage is cool. i like the garage better than the running board.