Showoff Your Rock Sliders

I didn't think he was offering them for the 3rd gens yet.. What length are they overall and how much did you end up paying?
 
ARKRWLR said:
I didn't think he was offering them for the 3rd gens yet.. What length are they overall and how much did you end up paying?
Click to expand...

He hasn't officially released them because I'm the official test fit. Once I get mine welded on they should be added to his website. That will be by the end of May, hopefully sooner.

The sliders are 68" sliders available with and without a kickout.

No kick out $290.00

With Kick out $325.00

Powder coating is an extra $100 and filler plates are ~$125 more.

The turn around time is 8-12 weeks right now because of a group buy that I took part of. He is also working on some local contract projects, but should be closer to the 8 weeks side. They are definitely worth it though.

I got on a group buy so I was able to get %20 off. He will often do group buys when his current cue of sliders get low. I will make a post in the 3rd gen section if I see one going on.
 
Too much beef for me, especially with 'mad cow' going around now.
Might as well stick some wings on there...

Anyway, this is a zombie thread...
:infidel:FIRE:AK47::gun5:
 

Attachments

  • flying car.jpg
    flying car.jpg
    11 KB · Views: 4,334
Could be wrong, but I believe the adapter is used with a hi-lift. The adapter makes it so the round part of the slider sits in the hi-lift when jacking the vehicle using sliders.
 
Yeah, the "slider adapter" allows the hi lift to get a better hold on the slider tube to keep it from slipping off. I'm making one now as I have tubes all the way around the truck.
This way I'll always have a place to jack off.:biggrin2:
 
BAMF all the way! :D strongest non DOM slider you can buy
we use way better mount hardware than all of our competitors
IMG_20111010_104729.jpg~original

our mounting plates wrap around the bottom of the frame and fully mount to the frame instead of just the side
IMG_20111002_161005.jpg~original

you can order with or with out kicks outs
CameraEffects-76.jpg~original

_DSC2711.jpg~original


we don't mess around lol
liveJo5eg0.jpg~original
 
Last edited:
absalom said:
Those are nice, just too much money :(
Click to expand...

Most companies use chinese steel, even their DOM is chinese. all of BAMF's steel are 100% USA steel, thats why it cost more. BAMF hot roll steel sliders are stronger than any chinese dom sliders on the market.

i think most people know what company uses chinese steel so im not gonna name names.
 
CBI Offroad Fab - 3rd Gen 4Runner Weld-On Rock Sliders with the following upgrades: DOM Tubing, Dimple-Die Plating, Kickouts, and Black Powdercoat.

Below is my email response to CBI's customer-service follow-up questions:

hungwin jza80 said:

Nathan,

The shipping experience was great. The product arrived in good condition and without any noticeable damage. I have three highly modified vehicles and in turn have received many packages of varying sizes, shapes, weights, etc. and know how challenging it can be to protect, package, and handle items such as these heavy and awkward rock sliders.

My initial impression exceeded my expectations. Since all of the customization was done over the phone or via email, I was impressed that CBI Offroad Fab was able to meet my high level of expectations. Considering the substrate, the finished product is excellent - the powdercoat is smooth and even. Most of the weld splatter was removed and only the quality shows through. I have been modifying cars for well over ten (10) years and these are, in my opinion, high-end parts and one can see that time and care were spent in creating these.

My friend helped me weld on the sliders this past weekend (04/01) and everything went very smoothly. The frame plates were prepped and ready to go, so all I had to do was grind down and clean the truck's frame in order to accept the welds. The only concern might be the amount of actual plate welded onto the frame as I have a 1" body lift, so approximately 3/4" of the frame plates were not able to be welded to the frame and protrude vertically. The sliders were purchased and installed in preparation for a wheeling trip this upcoming weekend 04/06 - 04/08, so I can follow-up with any worthwhile feedback/updates.

My overall experience with CBI Offroad Fab was awesome!!! Eleven out of ten. 6 out of 5 stars. Nathan Wright was a pleasure to work with and was very communicative and quick to respond to many (!) emails, inquiries, and telephone calls. Thanks goes out to the guy(s) that fabbed the sliders as well. I would not hesitate to purchase anything from CBI Offroad Fab in the future, and in fact, the only holding me back is money!!!


Thanks again,

Hung

PS - I'm not on Facebook, otherwise I would leave you feedback there.
Click to expand...


DSC_7005_1072.jpg


My version of weld-penetration testing! We used a Lotus Development Hi-Lift Rock Slider Adapter that I got from ToyTec along with the R-CAMS (which you can see in the closeup shot).
DSC_7006_1072.jpg


DSC_7007_1072.jpg


Finished product! I had to tape it down along the length because it was getting cool as I was applying the antislip tape. And, 3M rolls the rough side "in" on the roll, so it kinda works against you during application. I even radiused the corners of the tape to an ~8mm curve. Not shown in these pics is the tape applied to the kickouts. I had to figure out how to lay it out to fit the curves of the kickout and it had been a long day by this point.
DSC_7009_1072.jpg


DSC_7012_1072.jpg


DSC_7014_1072.jpg
 
SCRunner12 said:
He hasn't officially released them because I'm the official test fit. Once I get mine welded on they should be added to his website. That will be by the end of May, hopefully sooner.

The sliders are 68" sliders available with and without a kickout.

No kick out $290.00

With Kick out $325.00

Powder coating is an extra $100 and filler plates are ~$125 more.

The turn around time is 8-10 weeks right now because of a group buy that I took part of. He is also working on some local contract projects, but should be closer to the 8 weeks side. They are definitely worth it though.

I got on a group buy so I was able to get %20 off. He will often do group buys when his current cue of sliders get low. I will make a post in the 3rd gen section if I see one going on.
Click to expand...

They are 20% off right now!!!
20% off BAMF sliders - Tacoma World Forums
 
SCRunner12 said:
Mike, go with BAMF (Bayareametalfab.com). I will have mine on in a few weeks and he is local. Right in Benicia. They are a hybrid design and super beefy.
Click to expand...

Thanks Robert, I didn't know he was offering them for 3rd gens. Nice score for you! and 20% off group buy ain't bad either. Now the question... can I wait 8+ weeks ???? :cry2:
 
Last edited:
TheeMikeB said:
Thanks Robert, I didn't know he was offering them for 3rd gens. Nice score for you! and 20% off group buy ain't bad either. Now the question... can I wait 8+ weeks ???? :cry2:
Click to expand...

Trust me it's worth it. With the 20% off going on now it will cost just about the same as 4xinnovations (shipping included) and is a lot cheaper that the other options. I will be getting mine welded on the first week of June and will have pictures up then.
 
t4r4life said:
our mounting plates wrap around the bottom of the frame and fully mount to the frame instead of just the side
IMG_20111002_161005.jpg~original
Click to expand...

I know it would be easy to cut off the lower tabs, but that seems like a limitation for those with a body lift? Do they make longer plates then if you do have a body lift??
 
You must log in or register to reply here.

Members online

No members online now.
Total: 641 (members: 0, guests: 641)

Forum statistics

Threads
278,312
Messages
3,554,083
Members
248,016
Latest member
Advally Service

Share this page

Trending content

Back
Top