What Did You Do To Your 3rd Gen Today?

[Evilmunkey]

Drove her to work and soon to clean and paint the wheels bronze w/ Duplicolor High Temp wheel paint. . imp:

 

[4Running Daily]

Installed 255/85 KM2's. Only the rear rubs? Isn't that crazy.

Untitled by 4Running Daily, on Flickr

 

[paddlenbike]

3/4" wheel spacers paired with the Sequoia wheels.

The next day I got to test them pulling out a stuck park ranger.

 

[1blink]

Installed extended sway bar links finally, 3rd gen fronts on rear, 2nd gen rears on front. Moog.

You guys that disconnect one end and zip tie it out of the way while wheeling, what do you zip tie it to?

 

[shamading]

Replaced the drivers side mirror I broke with a powered (but non-heated) one from Rock Auto. Couldn't find the darn heated replacements.

http://www.toyota-4runner.org/3rd-gen-t4rs/145199-1999-limited-drivers-side-mirror-assembly-replacement.html

 

[Mauzer]

Last week I:
Installed read diff w/ 4.88's and ARB
Installed new ARB compressor
Ordered new 285 Cooper STT to replace pass rear balding tire

Tonight:
Get new tire mounted, then rotate tires
Run airline to rear diff (had to order parts for 1/4" conversion)

 

[lowlinkin]

Installed 255/85 KM2's. Only the rear rubs? Isn't that crazy.

Untitled by 4Running Daily, on Flickr

I've got the same tires on my fj and love them I was curious if they would fit with minimal rub on the 4runner.

 

[evort]

One of the wires to my drive side fog light broke.

I bought a new connector and 2 new wires and rebuilt the end of the harness.

Lo and behold...it worked.

I wasn't able to solder the wires together so after I twisted them together I ran a piece of heat shrink over the top. Hopefully it will hold for a while.

 

[t3chfr33k]

mounted my transmission radiator tonight

 

[4Running Daily]

I've got the same tires on my fj and love them I was curious if they would fit with minimal rub on the 4runner.

I'm rubbing on the rear bumper and that's it, so far.

 

[smkd13]

One of the wires to my drive side fog light broke.

I bought a new connector and 2 new wires and rebuilt the end of the harness.

Lo and behold...it worked.

I wasn't able to solder the wires together so after I twisted them together I ran a piece of heat shrink over the top. Hopefully it will hold for a while.

Another way you can do this if you don't solder them is by stripping the plastic coating off of crip type terminals and then crimping and then heat shrinking. Just an idea for you that I have use. I have a torch now so everything is getting soldered period lol

 

[evort]

Another way you can do this if you don't solder them is by stripping the plastic coating off of crip type terminals and then crimping and then heat shrinking. Just an idea for you that I have use. I have a torch now so everything is getting soldered period lol

Thank you.

I will go back and solder it later, I can't leave it like it is, I just can't.

 

[smkd13]

Thank you.

I will go back and solder it later, I can't leave it like it is, I just can't.

Good man. Was just giving the option of other ways to do it too

 

[slapdappy]

99 ltd

installed dual Hella horns and PA speaker for cb. Mounted so as not to block radiator.

 

[98LimitedBKN]

Ultimate Lift

Ordered my Toytec Ultimate Lift today! Can't wait to get it and hopefully get it set up next weekend!

 

[AlpineCoder]

Got the ShrockWorks rear bumper / tire carrier on:

 

[Skidmarcx]

Looks sweet!

 

[alaskaflyer]

Just playing around with some TRD decals I picked up.

 

[ugamurph]

Got the ShrockWorks rear bumper / tire carrier on:

Looks great. How long from order to delivery? I'm ordering their front bumper next week.

 

[AlpineCoder]

Looks great. How long from order to delivery? I'm ordering their front bumper next week.

The front was just under 5 months, and the rear was just under 7 months from order to delivery. Seems like it's sort of luck of the draw with them, but I'd plan on a solid 6 months. Check out my build thread if you want some more pics of the front.