What Did You Do To Your 3rd Gen Today?

Status
Not open for further replies.
stereo showed up. Modest but better than stock :guitar3:
 

Attachments

  • 20170613_070506_resized.jpg
    20170613_070506_resized.jpg
    134.5 KB · Views: 495
Nothing. Typical forum hype.
See ya on the side of the road in ~15k miles then... Make sure your AAA towing is paid up.

Seriously, there is a whole thread on cut open stock vs. aftermarket LBJ's. There is a huge difference in the quality of the OEMs vs any of the aftermarket parts.

My originals with 270k on them still were pretty good. Many on here have had aftermarket go bad in 15k miles or less. It is actually CHEAPER to run OEM in this case.

-Charlie
 
See ya on the side of the road in ~15k miles then... Make sure your AAA towing is paid up.

Seriously, there is a whole thread on cut open stock vs. aftermarket LBJ's. There is a huge difference in the quality of the OEMs vs any of the aftermarket parts.

My originals with 270k on them still were pretty good. Many on here have had aftermarket go bad in 15k miles or less. It is actually CHEAPER to run OEM in this case.

-Charlie

I had duralast gold LBJ. Lasted about 30-40k before they were making A LOT OF NOISE and one had A LOT OF PLAY. Thank god it did not break on me. But made me switch over to OEM right away.
 
Passenger mirror decided to "shuffle off this mortal coil...".
So after asking around, it turns out the local hardware store has a dedicated section for cutting mirrors and glass.
This may not seem all that great to you, but here its quite surprising.
Made my day much easier.
$5.00 and some outdoor double sided tape and I'm back in business.

zionxix-albums-my+4runner+stuff-picture46411-mirror-replacement.png
 
Last edited:
Got my new tires dirty... :guitar2:


Then got 'em clean again. :rockon:



Decent drop off here if not paying attention. No texting while 4Running!


Lots of great scenery in Utah, and not just in the Southern part of the state.


Justin :usa2:
Where was that at? I'd like to check that out.
 
Conicelli Wins

you searched for lbj failure, but not aftermarket lbj failure.

What is the failure rate of those specifically not including the normal recall failure.

oem lbj are 103 from camelbak

Just purchased from Conicelli for $94.95 a piece. Was going to use Amayama but by the time shipping is included the difference was negligible. They've also got OTRE's for $50 bucks a piece while you're in there.
 
Full time 12V Power Mod

I've been considering doing a full time 12V power mod to all of my power points but it wasn't until this recent trip that it became higher on my "to-do" list. I mentioned it in my build and [MENTION=91393]papabeach[/MENTION] recommended a link for me to JA's Toyota Highlander site which BTW I have had as a favorite for quite some time.

Anyway, here's the link to the mod: Thanks Papabeach! Very pleased. Full time 12V Power
 

Attachments

  • Fuultime 12V Power Mod.jpg
    Fuultime 12V Power Mod.jpg
    141.5 KB · Views: 348
stereo showed up. Modest but better than stock :guitar3:
Installed the same headunit in my 99 last night. Got to messing with it today and it's pretty nice. I installed the Rockford Prime speakers, cheap but they have decent sound for my listening uses.


Sent from my Nexus 6P using Tapatalk
 
Installed my custom CO2 tank bracket on my 4x4labs ladder. Bracket is made of Aluminum. I also had a Drop Down Table made, but I didn't install it
07e64bea9eee616b5dc24580ae70da4b.jpg
6f98202e37475dda92509184c1e52b8b.jpg
0ddb19bacc6397c1039762ae0dd72d0b.jpg
d96f778b38c284be8908fd17c0182b93.jpg



Sent from my iPhone using Tapatalk
 
Installed the same headunit in my 99 last night. Got to messing with it today and it's pretty nice. I installed the Rockford Prime speakers, cheap but they have decent sound for my listening uses.


Sent from my Nexus 6P using Tapatalk
Nice, I've come to notice I either have kids or a Dog or Both in my car, so Loud is a thing of the past lol. :drum:
 
It is from the FJ Cruiser. I believe that it was optional or it came with an optional subwoofer.

Awesome, thank you! I have one actually lol.. well my work does, I work in a salvage yard selling used parts in WI. Random I have one, but I really like how it looks in the dash I'll be doing this I believe

:vader:
 
Today I 3D scanned the rear of my truck so I can design and build a rear bumper in CAD and have it cnc cut. Super excited to start this build.

34874404265_c1560b237f_c.jpg


35270273226_683f5eddd3.jpg
 
Last edited:
Tint matched my front windows. And built a headliner storage rack, plan on keeping my goal zero solar panel up there and other small items.
 

Attachments

  • IMG_0640.JPG.jpg
    IMG_0640.JPG.jpg
    142.5 KB · Views: 472
  • IMG_0641.JPG.jpg
    IMG_0641.JPG.jpg
    134 KB · Views: 487
  • IMG_0644.JPG.jpg
    IMG_0644.JPG.jpg
    126.7 KB · Views: 484
[MENTION=105773]busmup808[/MENTION]

Can you provide more information on the swing down table, like how it attaches at the hinge, how it is supported when down, how it is locked in the upright position, etc.?

I'd like to add one to my swing out but yours is the first one I've seen that has a similar construction to my swing arm.
 
What did you do to your 3rd gen today?

Stretched out my new shoes. Really like how the 34x10.50's tuck into the fender wells. Very little rubbing even with spacers.

9342b7d8dec9419ee0e85829f01d3448.jpg


fe5dcbc4d17f5bc2941b649e43cf8a35.jpg


Started fitting the cb and running wires but ran out of time.

b292b54823421da7c976db15f55dafbe.jpg


afbeede3a936f0abd2cb8d837b9cd141.jpg


Also built a shelf for auxiliary power

a7ae7451cbbd49f55d3c0080eff63d65.jpg



Sent from my iPhone using Tapatalk
 
Last edited:
Status
Not open for further replies.

Members online

Forum statistics

Threads
278,316
Messages
3,554,120
Members
248,016
Latest member
Advally Service

Trending content

Back
Top