sogoood
New member
And have been working on this in my spare time
Youre an amazing artist! good shit!
What Did You Do To Your 3rd Gen Today?
- Thread starter pin8246
- Start date
- Status
Youre an amazing artist! good shit!
TejasRunner01
New member
Installed white LEDs into the dash column. Super happy there were no hot spots. I wanted to do blue, but honestly I am digging the clean white!
Sent from my A0001 using Tapatalk
Sent from my A0001 using Tapatalk
lienserolf
New member
Unfortunately, it is temporary decommissioned at the moment. I was parking on the street and the left driver side axle came off just as I was backing in.
Road Bull
Senior Member
I see I have some competition. Heading to screen printer tomorrow to get a few hundred made. :artist::third:
Attachments
sogoood
New member
fourfive
Senior Member
Hilarious
Roamed YT
New member
Well, on your way up, after stopping for a soak at Liard, if you need a garage to wrench in let me know. I'm in Whitehorse so only 950km from the Elephant Cage or 1100 from Anchorage.
Just bring me some Broken Truck (the beer, not the Toyota!) or Notorious Triple and we'll be set.
JZiggy
Senior Member
That's kinda how 5th gens look to me all the time! :tape:
Well, on your way up, after stopping for a soak at Liard, if you need a garage to wrench in let me know. I'm in Whitehorse so only 950km from the Elephant Cage or 1100 from Anchorage.
Just bring me some Broken Truck (the beer, not the Toyota!) or Notorious Triple and we'll be set.
thanks
in taking the ferry, part of my bucket list and less wear and tear on fully loaded 4runner
but seriously, thanks for the offer
4Runner4Leon
Senior Member
New battery! I first went to Home Depot to get the Exide Extreme, but decided against it as soon as I saw the lack of water filler caps. So I went to Wally World and got the Ever Start MAXX.
Ned Preston
New member
Brake Job
Did pads, rotors, shoes and new drums. But all looks good now.
Did pads, rotors, shoes and new drums. But all looks good now.
96RedRunner
Senior Member
Getting closer to garage time yea!! list is long.
Picked up regeared rebuilt rear E-locker diff this morn sitting next to E-locked regeared rebuilt front diff and fresh built locker axle housing,
waiting on Upper reinforcements from [MENTION=28464]eimkeith[/MENTION] to go with PCK n lower reinforcements.
Have rear locker harness completed, using Harrop harness front both ready to go in with LandCruiser switch. Andy mod ready to go.
TB kit install, Winch install, Transgo kit install. Ha, gona be busy for a day or 30.
While axle n diff are out sure I'll find something needing wire brushing n paint.
Picked up regeared rebuilt rear E-locker diff this morn sitting next to E-locked regeared rebuilt front diff and fresh built locker axle housing,
waiting on Upper reinforcements from [MENTION=28464]eimkeith[/MENTION] to go with PCK n lower reinforcements.
Have rear locker harness completed, using Harrop harness front both ready to go in with LandCruiser switch. Andy mod ready to go.
TB kit install, Winch install, Transgo kit install. Ha, gona be busy for a day or 30.
While axle n diff are out sure I'll find something needing wire brushing n paint.
jkeith.w
Official Vendor
96 ToyRunner
Member
Installed a catalytic converter and a rear o2 sensor at 330,338 miles
octanejunkie
Elite Member
Got my report from Blackstone Labs today 
i just bought my 4runner and it already had new control arms and tie rods as well as ball joints. i noticed it had a pull while driving so i had it aligned today. which i heard is kind of difficult because of the modifications made to it, like the 2 inch lift and larger size tires.
RS Dude
Member
Got my report from Blackstone Labs today
Such a long oil chg interval shows the cost effectiveness of using synth over dino.
:Took on the P0420 by the horns today. New O2 and A/F sensors and cats. I kept the original rear cat since it only looked like it was plugged up by the grenaded front cat. The honeycomb material in the rear cat look in tact, so I might try to clean it and sell it, or keep it as a backup.
No codes yet, but I'll have to confirm that it's gone after 200 miles or so. Truck is also louder and the distinct 5VZ-FE exhaust rumble has returned. Anyone dealing with this issue should consider doing this if a 3rd Gen has more than 200K miles. There likely won't be any other fix if you're certain that there are no exhaust leaks or the sensors are new. You can see the original cats below with 272,000 miles on them. I bought my truck in January with 268K on the odometer and can't believe I let myself drive 4K miles with the cats in such bad condition.
All that gray stuff from the floor was from the front catalytic converter.
New aftermarket catalytic converters.
This is the material from the front that was plugging up the rear cat
No codes yet, but I'll have to confirm that it's gone after 200 miles or so. Truck is also louder and the distinct 5VZ-FE exhaust rumble has returned. Anyone dealing with this issue should consider doing this if a 3rd Gen has more than 200K miles. There likely won't be any other fix if you're certain that there are no exhaust leaks or the sensors are new. You can see the original cats below with 272,000 miles on them. I bought my truck in January with 268K on the odometer and can't believe I let myself drive 4K miles with the cats in such bad condition.
All that gray stuff from the floor was from the front catalytic converter.
New aftermarket catalytic converters.
This is the material from the front that was plugging up the rear cat
- Status
Similar threads
