What did you do with your 4runner today?
- Thread starter NorthGa4R
- Start date
emelianenkov
New member
Pretty sure I have a cracked header. When I rev the engine, the leak sounds like the high pitches whirring of a weed whacker. URD time!
Relentless
New member
Just finished building and installing these on my gfs 05.
KingPrat
New member
One picture of my interior LED swap. This was insanely simple! Only complaint is that the LEDs only work one way, and I never got it right the first time....
Daylight contrast is minimal. Cant wait to check it out tonight. Still waiting on my rearview mirror wiring harness and that'll go in next, and am going to attempt the Map Light mod.
Daylight contrast is minimal. Cant wait to check it out tonight. Still waiting on my rearview mirror wiring harness and that'll go in next, and am going to attempt the Map Light mod.
Last edited:
emelianenkov
New member
One picture of my interior LED swap. This was insanely simple! Only complaint is that the LEDs only work one way, and I never got it right the first time....
Daylight contrast is minimal. Cant wait to check it out tonight. Still waiting on my rearview mirror wiring harness and that'll go in next, and am going to attempt the Map Light mod.
Good comparison of the two bulbs!
I wanna do LED interior lighting as well, but I've never been a fan of cool white.
zopperman
Moderator
Does your HU have 4 RCAs? (2 sets)
HHIRunner
New member
Yes It does
piccrazy30
New member
Now I must go wash the dirt off!!
Doozi
New member
Just finished building and installing these on my gfs 05.
Nice sliders!
Casper421
New member
Just finished building and installing these on my gfs 05.
Looks b!tchin!! Do you have more straight on and side profile pics? 3/16" plating?
momo.75
Registered User
Went wheeling today and flash flooding was pretty bad through the Mojave river area. I ALMOST got stuck a few times,
it was covered in mud and it took about 2 hours with the pressure washer to get it cleaned. The mud stunk toouke:
oh well atleast it cleaned up well.
Looks good both ways! When are you getting a rear bumper?.....:gossip:
momo.75
Registered User
Thanks. I dunno I kinda like the swing gate , I m not really fond of bulky rear bumpers. The price difference I could afford a supercharger kit
Very true!.....:usa2:
S p a r k y
New member
Lots of work today! Will try and get pics tomorrow or sometime! Added billies set at 1.75 to front, put in toytec super flexes in rear with daystar 1.5 driver side. Took advantage of lifetime advanced auto cv axles and put some new ones in, added a diff drop kit!
So front end is: FJ coils with bilsteins set at 1.75 with a daystar budget boost topout spacer (inch thick poly, net almost 2")! Some of you will question me, but I have a friend who has similar and has been working great. The measurements for that set up puts the front at 38 1/4 driver side, 37 3/4 on passenger, that 1/2 drives me crazy, may look and see if i can do something. this setup is slightly less than guys running OME's with billies at .85! Everyone that is at that height gets stock UCA's in spec, so that's what will happen for now!
Rear with supers and daystar 1.5 on driver side is: driver 39.25 passenger 38.5! I'm going to run this for a few days and see if it settles, if the 3/4 diff stays I plan to cut the other 1.5 I have down some to make them even. I know some may not care about the .5 and .75 differences but I can see em and they bother me!
So front end is: FJ coils with bilsteins set at 1.75 with a daystar budget boost topout spacer (inch thick poly, net almost 2")! Some of you will question me, but I have a friend who has similar and has been working great. The measurements for that set up puts the front at 38 1/4 driver side, 37 3/4 on passenger, that 1/2 drives me crazy, may look and see if i can do something. this setup is slightly less than guys running OME's with billies at .85! Everyone that is at that height gets stock UCA's in spec, so that's what will happen for now!
Rear with supers and daystar 1.5 on driver side is: driver 39.25 passenger 38.5! I'm going to run this for a few days and see if it settles, if the 3/4 diff stays I plan to cut the other 1.5 I have down some to make them even. I know some may not care about the .5 and .75 differences but I can see em and they bother me!
Similar threads
