What did you do with your 4runner today?

Installed a CB. Not a professional job but at least no holes were put in my rig.
b8a054e3c040d31ab8f252d89d5db387.jpg


16bb2e2d8e0a76a74d7731447674916b.jpg
 
iAlex684 said:
bdbe79d6b20dad11e9114b43dce9bcb8.jpg


Installed my new headlights and wired my halos [emoji16] I want a roof rack so I can out a tire on top [emoji12]
Click to expand...

That set up is gorgeous.. I have to ask.. where did you get the halo for your fogs? Well I mean is it pre built that way or does that company have them for any cube?
 
Blackhawk_194 said:
That set up is gorgeous.. I have to ask.. where did you get the halo for your fogs? Well I mean is it pre built that way or does that company have them for any cube?
Click to expand...



They're prebuilt this way, you can go on Amazon and purchase them I believe the company was nicolighting. There is also alternatives, if you have lightbars or pods already LEDconcepts offers halos for them but you'll have to install it or get someone to install them.
 
Finally put my skid plates back on after coating them in Bed liner paint. My runner is a beach vehicle, and the sand and salt is rough. Hopefully this will last a few trips
 

Attachments

  • image.jpg
    image.jpg
    141.5 KB · Views: 533
calvinv8sr5 said:
Which size did you go with
Click to expand...

Largest - I'd love to find one a couple of inches bigger, but after some searching I couldn't find anything.
I believe if you message the seller you can get a larger version from them but it would be two different pieces because their printer only does 23-24"
 
Swapped in new left front axle ... OReilly's CV so I can rebuild the OEM, which is definitely a keeper and definitely looks stronger.

I think I get a break from under vehicle work til next week [emoji38] looking forward to CBI bumpers so much.
 
took it golfing (yesterday)... Considering where I hit some of my shots I could of used it out there on the course to get me to my ball out of bounds a few times. yikes! more practice needed... haha
 
Chased down a rubbing sound on the dustcover after the axle swap … ended up putting in new brake pads and ordering Lexus wheel studs (ARP1007715) [emoji848].

Researched DIY skid plates ... don't want to directly bite anyone else's design, but would love to see a mounting hole pattern template ... seems like a cardboard mock up is in my future. I'll post a generic pattern if I don't find one out there anywhere.

Emptied a few mags at the range and put the new axle and brake pads to work [emoji12]

acebdeff5fafe3a8213bb71479833a49.jpg
 
28e5d53f12a8340413e985a1614adbf5.jpg


a3486c1b68acaee62d45b2c805a6e7a0.jpg


Finished the boat and started on my roof rack today, should have it done tomorrow. 3/4" EMT is super hard to weld... Running 3/32" 6011 at 50 or so. Wishing my wire feed setup wasn't already loaded up with 045.


Bonus boat pics

74b7b698292145bb82119c183f334650.jpg


29e728b556a7091eb039c19c30cb5d1c.jpg
 
Last edited:
Did a thorough cleaning on the throttle body and maf ... Was very very dirty now looks like this :)
 

Attachments

  • image.jpg
    image.jpg
    129.5 KB · Views: 423
You must log in or register to reply here.

Similar threads

F
Extended Lower Control Arms for 4th Gen?
Replies
4
Views
45K
aemravan
A
0
New 03 4.7 with over 300k miles questions.
Replies
19
Views
3K
04run&gun
0
B
Opinions needed related to my fuel pressure loss vapor lock issue..
Replies
12
Views
4K
JustTroItIn
JustTroItIn
T
2001 4runner Head Gasket Replacement
Replies
19
Views
16K
alia176
A
F
3rd gen 4runner cooling question.
Replies
19
Views
4K
gh25_
gh25_

Members online

No members online now.
Total: 569 (members: 1, guests: 568)

Forum statistics

Threads
278,316
Messages
3,554,112
Members
248,016
Latest member
Advally Service

Share this page

Trending content

Back
Top