riceandpho
Elite Member
did these few days ago, new white leds to replace the blue. these are flat top leds, seem to spread the light out better.
What did you do with your 4runner today?
- Thread starter NorthGa4R
- Start date
Bluesky 07
Senior Member
Forgive my ignorance, but what are those for? Reminds me of the Viper launch tubes on Battlestar Galactica.
riceandpho
Elite Member
just additional alarm leds. the one down at the corner is actually wired to the alarm brain status output. the scanner leds are wired to the ground when arm output.
Bonesetter
New member
Mullett757
New member
I was actually just looking at these at discount tire this morning and wondering what they'd look like on the 4runner. solid looking wheels on it!
cloud
Banned
Tested my center diff locker, and 4x4 actuator, cleaned the MAF and throttle body, replaced coolant with Toyota red, got my first scratch on my sliders that I welded on a few days ago. Now to scrub surface rust and paint the sliders and frame around the plates.
Rear diff fluid, transfer case fluid, bearings, lower ball joints, and steering system are all that's left for a total refurbish job. Just might get 35's mounted by the end of July.
Then I can weld gussets to the shock towers and spindles!
Sent from my XT1710-02 using Tapatalk
Rear diff fluid, transfer case fluid, bearings, lower ball joints, and steering system are all that's left for a total refurbish job. Just might get 35's mounted by the end of July.
Then I can weld gussets to the shock towers and spindles!
Sent from my XT1710-02 using Tapatalk
vipergrhd
New member
Part number?
Would happen to have a part number? How much was it? Plug and play?
“Smokers Kit” with double 12v’s installed. Easy-peasy. Need to re-wire the other 12v the PO drilled in there instead of just fixing the OEM socket in the original piece.
Would happen to have a part number? How much was it? Plug and play?
The part number is 74110-35010-B0. I literally installed mine in the parking lot of the dealer when I picked my car up in Philly.
Here's a install post from another member.
http://www.toyota-4runner.org/engines-suspension-wheels-tires-audio-accessories/52158-smokers-kit-extra-12v-outlet-installed.html
I got mine off ebay for $23.50 shipped. Would have been less but I wanted it to be at the destination by time I picked up the car so I had to go with something that had a for sure shipping date. You can save a few more bucks if you shop around.
Last edited:
Bonesetter
New member
Yep, got 'em at Discount Tire. They knocked off the price of one wheel (I got 5) and the install fee (possibly because I got the BFGs from them the week before). Great customer service with those guys. I'm having more front fender rubbing now with the different offset, but I'll be remedying that with a fender mod later today.
Sporin
New member
I got mine from ebay https://www.ebay.com/itm/New-OEM-To...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649
$23.96 with free shipping and I had it on my doorstep in about 3 days.
easyeatlanta
New member
Got the Rola rack, low profile 4xinnovations mounts, 32in light bar all mounted this weekend.
Mounted my hi-lift, spare wheel, and knock off maxtraxs
Gunna get some locks etc, to keep everything from getting stolen.
Mounted my hi-lift, spare wheel, and knock off maxtraxs
Gunna get some locks etc, to keep everything from getting stolen.
slimjj
New member
Got the Rola rack, low profile 4xinnovations mounts, 32in light bar all mounted this weekend.
Mounted my hi-lift, spare wheel, and knock off maxtraxs
Gunna get some locks etc, to keep everything from getting stolen.
Do you have aftermarket turn signal indicators or did you figure out how to clean them. Yours are so shinny and new looking, me jealous!
Sent from my iPhone using Tapatalk
slimjj
New member
cleaned and sealed my headlights
imag0955_42426136315_o by tuborg_14, on Flickr
imag0956_43329620141_o by tuborg_14, on Flickr
imag0966_42612500674_o by tuborg_14, on Flickr
imag0968_43329573441_o by tuborg_14, on Flickr
imag0965_41520169400_o by tuborg_14, on Flickr
I did the same thing this weekend! Couldn’t believe that it even got rid of the crazing on my lenses, thought that was permanent. Need some clear right quick. Ordering some Sylvania UV Block Clear Coat.
Also replaced the rear sway bar bushings and end links and installed the newer FJ Springs I’ve had for a few months. Rear diff and transfer case fluid change, oil and filter change, new spark plugs, cleaned up battery terminals, greased the prop shafts (u-joints and slips), MAF cleaned, TB cleaned, inspected brake calipers (no sticky) and regressed the slide pins, and touch up paint on the hood scoop grill. Whew, long weekend.
Now to deal with the front diff drain plug that I mucked up :/. Why oh why did Toyota use a 10mm hex aluminum drain plug on that damn thing? Way too soft for 49 ft/lb
Sent from my iPhone using Tapatalk
easyeatlanta
New member
replacements off of ebay. my old ones were bad.
momo.75
Registered User
When i had my stock front bumper/turn signals i switched out the bulbs for some chrome coated bulbs. The purpose of this is to get rid of the egg yolk look, leaving them looking clean. I also use them in my tail lights. You can check them out here.
Chrome Stealth Dipped Platinum Titaniuim Silver Vision Xenon Bulb
Chrome Stealth Dipped Platinum Titaniuim Silver Vision Xenon Bulb
Similar threads
