KneeCaps build thread/DIY/Vehicle story/Lots of Pics

If you follow me on Instagram at JLS_KNEECAPS everyone would have seen these pictures. But for those you that don't here's what we've been up to...

We took at trip with some friends up to northern VA for a long weekend to go skiing/snowboarding and get snowed in.

Found out that a Thule cargo carry bag fits perfectly in the rack in front of the RTT and fit four suitcases that no one had room for.



Start of the storm that dropped 36" total on us in 2 days...



After a hour of digging out of the snow bank that was created between a wall and my friends suburban she was free.




Mounds of snow.




The afternoon we left there were clear sky's

 
Love this thread. Is it bad that I can read these build threads on forum for hours and haven't picked up a book in over a year? :help: Ha ha
 
Good Looking Out!

CplTurner said:
Please don't waste your money on the expensive Gobi shocks...These are what you seek:

Strong Arm 6156 Gas Charged Liftgate Lift Support | Cadillac | Chevrolet | GMC

When you order, you must put in the comments section the following: "Convert to 10mm straight ends"

I have been running these for about a year and they are a good bit stronger than the stock struts.
Click to expand...

Thanks for sharing this info. I modified my original order and ordered these instead for 1/3 of the cost!

Have you tried these out with anything else loaded on your ladder? I am planning to hang my Treds and Trasharoo off the ladder and it would be a nice to have if I didn't have to unload the Trasharoo to get into the back. That load may still be too much even for the upgraded Gobi gas shocks, but hoping you may have some experience to share.

Thanks again.
 
KneeCaps said:
mounting plates are 9" long, 1"wide

risers are 2" from bottom of notch to mounting plates

cross bars are 44.5" from notch to notch

spacers that are between the bottom and top hoop are 1.5" from notch to notch

fairing is 7" tall and 43" wide

front "feet" are 2.5" long 1" wide and the riser is 2.5" from plate to notch

hope that helps a little.
Click to expand...

So it may be a long shot, but do you have any build plans for your rack? I'm trying to make one myself and I want to get some ideas on where to start.
 
littlezavasaurus said:
So it may be a long shot, but do you have any build plans for your rack? I'm trying to make one myself and I want to get some ideas on where to start.
Click to expand...

I had a rough sketch on a piece of paper(that's way long gone), and I just barely went off that to be honest. only thing I can say is take the factory rails off, make your base plates that bolt to the truck and go from there. just look over the pictures in order and that kinda gives a step by step process.
 
KneeCaps said:
I had a rough sketch on a piece of paper(that's way long gone), and I just barely went off that to be honest. only thing I can say is take the factory rails off, make your base plates that bolt to the truck and go from there. just look over the pictures in order and that kinda gives a step by step process.
Click to expand...

haha i figured you didn't. Alright sounds good, thanks
 
so you will notice my name on here as changed, same guy just different name. This should connect all the dots across social media when we post something and people will instantly know who its from.
 
Great build. I am new-ish to the site and have been looking to go to Uwharrie for some time now. Seems like a lot of the guys who commented on your thread are from NC. Let me know if you get a group going, I would love tag along and offroad with some people that know what they are doing.

Just started the build but right now running pretty much stock 2013 T4R Trail.
 
ClimbOn said:
Great build. I am new-ish to the site and have been looking to go to Uwharrie for some time now. Seems like a lot of the guys who commented on your thread are from NC. Let me know if you get a group going, I would love tag along and offroad with some people that know what they are doing.

Just started the build but right now running pretty much stock 2013 T4R Trail.
Click to expand...

http://www.toyota-4runner.org/5th-gen-t4rs/214627-uwharrie-ohv-2016-meet-up-thread.html

That should help you find someone to go with you if we cant work something out. We plan on going a lot this year so im positive we can have a meet up you can come to.
 
Been awhile since I've updated this build thread. If you have been following us on Instagram and Facebook you have seen this stuff. If not here ya go!.…

We went camping a few times over the winter. We managed to not get caught in the snow once. Even when they were calling for it!



Spring time came and we attended the jamboree at uwharrie...



Also camped at the beach with the local Toyota club.

 
Early summer decided one Saturday morning to go up the front side of Daniel at uwharrie...

Made it up. Won't do that again for some time. Took some beating on the way up.






 
You must log in or register to reply here.

Similar threads

J
JoeyV's 2012 Build Thread.
Replies
14
Views
37K
MDFI29
M
A
Time to pull the 4.7 out :-(
Replies
9
Views
3K
alia176
A
calimobber
Lots of Mods
Replies
3
Views
2K
calimobber
calimobber
YetiX
FS: 2006 4Runner Sport Edition 4WD - Denver, CO - $9,000 obo
Replies
3
Views
4K
YetiX
YetiX
M
FS: 4th Gen 2006 V6 4x4 Sport Edition - Washington, DC - $6300?
Replies
0
Views
1K
mssVT98
M

Members online

Total: 4,593 (members: 3, guests: 4,590)

Forum statistics

Threads
278,315
Messages
3,554,126
Members
248,016
Latest member
Advally Service

Share this page

Trending content

Back
Top