Mikey's Build Thread...

I like the idea!

Okki said:
I'm envisioning a large section of kydex or similar and "wrap" the tailgate area below the taillights and fold it round the sides (behind the steal) and finish off at the rear wheel well. This would be attached to the body, so it does not impact the bumper flex, protects the vents in a similar fashion as the OEM plastic does and makes the rear look a bit more finished when the hatch is open. can be heat contoured on the sides to still allow clearance as needed.

whatcha think?

Okki
Click to expand...

I don't how I missed this!? This fourm is moving fast these days.

Okki- I like the idea alot! Never used kydex before. What would be the best way for fastening the material in place; some form of adhesive?

Thanks for your input! :trophy:
 
MeBe4running said:
I don't how I missed this!? This fourm is moving fast these days.

Okki- I like the idea alot! Never used kydex before. What would be the best way for fastening the material in place; some form of adhesive?

Thanks for your input! :trophy:
Click to expand...

it looks like there are mounting screw locations that could be used that were used for the OEM plastic. This is best illustrated in your picture of the trim panel removed.
ybe3eqat.jpg


I'm guessing there would be similar options for the rear. You could also drill some holes and use factory-style push pins. (like used on the radiator shroud etc)

Okki
 
Bumper looks interesting. To date the Hefty Fab Rear Bumper was the clear standout. This design has a lot of potential to be aesthetically and functional.

I want to learn more about the extra ground clearance over the Hefty once this is finished. I also want to learn which one can ship completed to me for DIY installation.

I would be interested in seeing this bumper powder coated black and then the upper section painted sliver to match the looks of the stock truck. It looks like there is a good differentiation line where the swing arm mount is for the upper to be body color and the lower section to be black. Kinda like this, edited to mimic Trail Edition Fender arch.
2ihvwuf.jpg
 
Last edited:
Okki said:
it looks like there are mounting screw locations that could be used that were used for the OEM plastic. This is best illustrated in your picture of the trim panel removed.
ybe3eqat.jpg


I'm guessing there would be similar options for the rear. You could also drill some holes and use factory-style push pins. (like used on the radiator shroud etc)

Okki
Click to expand...

I see what your saying. I thought you where talking about doing it within the interior than the exterior. Thats is for sure a possibility. I might just brainstorm over that for awhile. Thanks Okki!
 
Got word that I should be picking the truck up early next week, hopefully. Luke said the bumper came out great. He was thinking that the trim piece below the tail lights, the stainless part, would be left un coated and let the metal color come out, the rest will be black.

Counting the hours down.
 
Ok so who is ready for some driveway photos with a cell phone? No, well here you go anyways.

20121110_153750.jpg


20121110_153555.jpg


20121110_153615.jpg


20121110_153650.jpg


20121110_153727.jpg


20121110_153740.jpg


20121110_154026.jpg


20121110_155228.jpg


20121110_153638.jpg


20121110_153626.jpg


Craftsman ship is BEAUTIFUL!!!!! I am extremely happy with the outcome. I have the three can holder with the tire carrier and hi lift holder setup to accomodate up to a 35" tire (it is adjustable too, being able to bring it closer to the truck or further away). The swing outs HUG the lines of the truck but not close enough to cause damage. There is plenty of space for flexing. The swing outs are also controlled by a hydro strut on each side and the latch is very sturdy and adjustable as the bumper ages.

For those that might be interested, here is the news. Luke can reproduce the bumper! If you are able to bring the truck to him he has jigs made and can build it on your truck. For those that are crafty and can weld, he is probably going to make it a DIY kit. Shipping? Give him a call or email.

You want photos of underneath you say? Ok...
 
Last edited:
Ok so the hitch is hidden...

20121110_153831.jpg


Not sure of the tow rating but I don't care cause i rarely do.

Three bolts on the bottom on each side...

20121110_153903.jpg


and a couple on the side...

20121110_153945.jpg


And extra plate was welded on with a nut to add an extra mounting spot for the bumper. This thing is not going ANYWHERE. Very well thought out and built.

I get my full size spare on Monday and going wheeling on Saturday so stay tuned for the dirt shots.
 
Last edited:
1) Hows the view from the backup camera; it looks like you have one installed?

2) What's your take on adding weather stripping on the side and under the tail lights?

3a) Are the swing arms removable? and 3b) if so, is the under body spare hoist still accessible?

And last but not least... Does Luke have any friends closer to Indianapolis that can do the install because driving to San Fran is a bit much for a weekend :D

I think you've officially convinced me on Luke's over Hefty Fabs bumper!

Thanks Mike!

Okki
 
Thanks for the pics!

I think your bumper is fantastic. Very detailed and skilled craftmanship has gone into that design. Love the finish as well.

One more image request. Could you post an image of the bumper with the rear hatch open? I would love to see the full surface area.

Can wait to see some "dirty" pictures of it :)
 
You must log in or register to reply here.

Members online

Total: 320 (members: 1, guests: 319)

Forum statistics

Threads
278,307
Messages
3,554,050
Members
248,016
Latest member
Advally Service

Share this page

Trending content

Back
Top