What Did You Do To Your 3rd Gen Today?

[bc toy]

Finally finished off my transmission transplant :clap2:
I am soooo glad that is over!!!!

 

[TNRunner99]

what coilovers are these? the boss coilovers?

They are the Toytec coilovers, Part Number TT-AFCS-600 on their site. I chose the 600lb springs because I have an ARB on the front.

 

[dirtbike250x]

Drove around the Pine Barrens

 

[lowlinkin]

Got my lift installed yesterday...alignment will come tomorrow.

 

[Coast2Coast]

Nice. The Power Wagon is no nimble beast. Some of those behind its wheel have learned the hard way:
Ram Power Wagon Flounders in Sand - PickupTrucks.com News

Rumours!

Power Wagon on Golden Crack 2011 - YouTube

Super nimble truck

 

[TheKorstjens]

got new signal housings and tinted them

 

[SST221]

Preventative maintenance

And while I was in there installed new 5100's on the 2nd perch with my tundra springs. Gained 1in. and sit at 24 1/4 from bottom of center cap running 265/70 BFG's. Old shocks were the stock billies from tundra set-up. Huge differance:thumb3:

 

[ugamurph]

They are the Toytec coilovers, Part Number TT-AFCS-600 on their site. I chose the 600lb springs because I have an ARB on the front.

We need to get together soon for another ride. What days (or nights) do you have off now? My RDOs are Wed/Thurs.

 

[Robb235]

Installed my external trans cooler to avoid a pink milkshake.

 

[TNRunner99]

We need to get together soon for another ride. What days (or nights) do you have off now? My RDOs are Wed/Thurs.

Yes we do. I'm back working midnights now so getting off work is pretty easy. Our off days are random so its hard to say what days I'm off. I can schedule a trip in anytime though. I'm itching to get out and ride, I've been taking my work car home now so my runner just sits in the garage. I think I drive it maybe once every other week now. I'm trying like heck to save for new tires after that lift. Wanting to get some mud terrains. Message me or send me a text and we can start making some plans.

 

[A.Wilson013]

Yesterday I finally got around to replacing my factory crossbars with a thule setup that I purchased a few months ago. MUCH more solid than the factory bars, and they lock.

They do whistle a bit at highway speeds. If I have the radio on I can barely hear it, but it is there. May have to buy a fairing.

 

[NJCatalana]

swapped out my gauge, dash, and shift lights to LEDs, the whole process went very smooth and was way easier than I had expected

 

[Rocky5000100]

swapped out my gauge, dash, and shift lights to LEDs, the whole process went very smooth and was way easier than I had expected

I just did this too! Went with white everywhere...looks much more modern.

 

[NJCatalana]

I just did this too! Went with white everywhere...looks much more modern.

yes it does! I did the Cool white, its bright enough but not distracting.

 

[Brilliant]

crafty

Finished another crafty project. A single din OE switch panel.

 

[patinthehat]

I went and got mine washed today and got all kind of compliments about how clean it was. Then i had a buddy stop by and i had to back him up to keep him from drooling on it lol. hoping to get my antenna fixed today!

 

[42s on u]

Got my lift and 35's on:cheer2:

 

[thor999]

Oil change, rear diff fluid replace, lubed driveshaft, and once again defeated by the drain plug for front diff... going to take it to a pro I guess...

 

[JWaldz]

swapped out my gauge, dash, and shift lights to LEDs, the whole process went very smooth and was way easier than I had expected

Looks good! Have a link to the specific led's you used? They don't seem to produce much hot spots or shaded areas like some led's do.

 

[Bama_Runner]

Installed B&M Supercooler 70264 and bypassed the factory tranny cooler to avoid the strawberry milkshake. My 4Runner has 200,000 on the factory radiator so I felt like I was living on borrowed time.