Bushwacker made fenders for the 5th gen!!

[adio3x]

I haven't read all the posts, but can one of you guys measure the height of the flare, especially the fronts. Thinking about adding more crap to my rig, but the snorkel might be an issue, cutting things is no issue for me at this point lol. Thanks in advanced!

 

[LawnDart]

I haven't read all the posts, but can one of you guys measure the height of the flare, especially the fronts. Thinking about adding more crap to my rig, but the snorkel might be an issue, cutting things is no issue for me at this point lol. Thanks in advanced!

It's 5.50 tall. So it absolutely will interfere with a snorkel.

We took one of the BW flares i purchased and could see plainly that it caused a problem. I don't mind cutting the flare but I just want to avoid spacers for a variety of reasons because they bump that far out.

 

[chudiddy]

I haven't read all the posts, but can one of you guys measure the height of the flare, especially the fronts. Thinking about adding more crap to my rig, but the snorkel might be an issue, cutting things is no issue for me at this point lol. Thanks in advanced!

They will definitely be an issue with the snorkel. Just ask [MENTION=124732]LawnDart[/MENTION]!

 

[LawnDart]

They will definitely be an issue with the snorkel. Just ask [MENTION=124732]LawnDart[/MENTION]!

Had Bushwhacker built these without the fake bolts that'd be halfway easier to installing (vertical height). The width is again the bigger issue for some of us.

 

[Magnetic4R]

I'm digging them more and more now. Looks like I may get these all.

 

[3wbdriver]

Took me about 2 hours start to finish, not counting washing it down to the OMG White and a couple smoke breaks. I also had to trim a 1 1/4" x 1 1/4" piece out of the front flares to fit over the square tube of the Shrockworks sliders. Knocked right out with a Dremel. Like chudiddy I am running 1.25" spacers, but with 8" wide wheels. Sorry about the pics. I keep forgetting OMG White and clear sunny skies do not make for good pictures!!!

 

[chudiddy]

^^Looks great^^

Hey I have the Black rear valence fully intact from my rear bumper available if you're interested.

 

[3wbdriver]

^^Looks great^^

Hey I have the Black rear valence fully intact from my rear bumper available if you're interested.

Quite possible. Please PM me a figure and we'll dicker.

 

[Mistaken]

I'm digging them more and more now. Looks like I may get these all.

Nice! I wanna see them on a Mag Gray 4Runner.

 

[Beer_Runner]

Nice! I wanna see them on a Mag Gray 4Runner.

I wanna see them on a quicksand Pro!

 

[3wbdriver]

I wanna see them on a quicksand Pro!

Mine was almost Quicksand colored before I washed it today. I had no idea how dirty it was until I washed it to install these. :shocked:

Here is a less bright shot.

 

[simonsay]

Took me about 2 hours start to finish, not counting washing it down to the OMG White and a couple smoke breaks. I did find out - purely by accident - the main rear fender pieces WILL fit over the factory flares. I didn't realize my passenger side one was still in place until I started picking up tools, and it doesn't seem to have hurt any of the alignment. I also had to trim a 1 1/4" x 1 1/4" piece out of the front flares to fit over the square tube of the Shrockworks sliders. Knocked right out with a Dremel. Like chudiddy I am running 1.25" spacers, but with 8" wide wheels. Sorry about the pics. I keep forgetting OMG White and clear skies sunny do not make for good pictures!!!

I think you need a few more stickers. :shocked:

 

[3wbdriver]

I think you need a few more stickers. :shocked:

Lol. What can I say, I'm an ex-racer. :becky:

 

[Magnetic4R]

Nice! I wanna see them on a Mag Gray 4Runner.

The Expedition Overland 4Runner MGM has the BW but the graphic and silver bolts are throwing it off for me. Can't really see the fender with the graphic distraction going on.

 

[F-stop]

I wanna see them on a quicksand Pro!

They'll be on mine soon. All my addons are in a pile in the garage waiting for the 4runner to come in next week.

 

[Mistaken]

The Expedition Overland 4Runner MGM has the BW but the graphic and silver bolts are throwing it off for me. Can't really see the fender with the graphic distraction going on.

Yup. I agree. Definitely need to see them on a vehicle that's more stock.

 

[white thunder]

2015 4runner sr5 premium 4x4

Just installed mine yesterday

 

[oljedi11950]

Looks good but agree with guys on black nut/bolt/screw cover !

 

[white thunder]

Yeah i thought about it but i figured it went with the machined rivets on my fuel wheels.

 

[Dogtown]

Yeah i thought about it but i figured it went with the machined rivets on my fuel wheels.

What offset are your wheels? It doesn't look like you are running spacers but those wheels make the tire nice and flush with the fenders.