Limited Edition Mod Thread

265/60r20

Anyone running 265/60r20 on the stock limited rims? Yes, I searched and am seeing no results other than someone asking the same question a couple years ago...

Would like to run true 32" set up with some more sidewall than the typical 275/55r20.

We have a 2016 Limited stock for now, but will be putting a slight lift on before I get the tires. Have the Eibach pro shocks front and rear and Eibach pro 1" lift springs for the rear. Deciding between the 1.75" and 2.5" setting for the perch on fronts. Want to maintain some rake so we don't do the Carolina squat when loaded up for camping/road-trips.

I think the tires should fit with just a fender liner adjustment, but if anyone has input I would greatly appreciate it.
 
bret56 said:
Transformation complete. 6 weeks ago this was a limited. You wouldn’t know that anymore. A lot of time and work has gone into this build. Happy to have it done (for now)
23172f0269d1479bf40ab94df62f4452.jpg

aea60be6c3af29ee294c2affeb01ad97.jpg

6d2ed414fea1bb01552734c3049b1872.jpg



Sent from my iPhone using Tapatalk
Click to expand...

what rims are those?
 
I welded up some Coastal Offroad sliders a few weeks ago, and then put the 4Runner back to work. I have the stock plastic pieces for the front where it meets the flare/fender, but haven't decided if I want to run the rocker protection down the sides or not. It's not quite as visible as I thought it might be.

R6N8sTyh.jpg

omHcyUQh.jpg

DUk6ZCwh.jpg

Xe5TQiHh.jpg
 
17Jetta said:
Anyone running 265/60r20 on the stock limited rims? Yes, I searched and am seeing no results other than someone asking the same question a couple years ago...

Would like to run true 32" set up with some more sidewall than the typical 275/55r20.

We have a 2016 Limited stock for now, but will be putting a slight lift on before I get the tires. Have the Eibach pro shocks front and rear and Eibach pro 1" lift springs for the rear. Deciding between the 1.75" and 2.5" setting for the perch on fronts. Want to maintain some rake so we don't do the Carolina squat when loaded up for camping/road-trips.

I think the tires should fit with just a fender liner adjustment, but if anyone has input I would greatly appreciate it.
Click to expand...



I am, I am. Dealer had them installed when I bought it new. BFG KO2's. Also had a front end level by RevTech. There is a slight rubbing on the front of the fender liner at full lock in reverse. BFG recommends a min. 7.5" rim but the stock 20's are only 7". No ill effects on handling or ride. I'm expecting that they may wear more in the center. When they need replacing, I'll go with the SCS Stealth 6's in 17" with 265/70R's like I did on my '13 limited.

Made the liner adjustment on the '13', but too old and lazy to do the '19'. Not that bad of a rub anyway. HAH!
 

Attachments

  • DSC_0706b.JPG
    DSC_0706b.JPG
    121.7 KB · Views: 1,933
Last edited:
17Jetta said:
@a47chuc thanks for the response. Sounds like 265/60/20's will definitely rub with the lift I'm planning.
Click to expand...

My leveling lift is only 1" maybe a bit more. I'm thinkin' you'll be OK. KO's also have very square shoulders. Another tire may be OK. Good luck!
 
tony2412medrano said:
That looks amazing I was thinking about doing the same how hard was it did you do it yourself? How about the sensor on the bumper
Click to expand...

I did do it myself. It was a little time consuming but other than that, not too difficult. I had a body shop paint my front bumper for me. I traced the hole from the limited front bumper using cardboard and then traced it on the front bumper of the offroad/pro front bumper but upside down since the angles are reversed between the two bumpers.
 
17Jetta said:
Where did you put the spring perch on the front? .85 or 1.75"? You put on the Eibach 1" lift rear springs? Looks good!

I have the Eibach pro shocks front and rear as well as the pro lift 1" springs for the rear sitting in the garage. Waiting for it to cool down before I do the install. Pretty set on going 1.75" in the front, but still considering the higher 2.5"...
Click to expand...


Thanks

Front perch is set to 1.75” and yes, the rear coils are the 1” lift Eibach’s.

I also considered going the 2.5 setting with a higher coil in the rear but didn’t feel comfortable with the coils being “pre-loaded” that much and assumed it would make the ride a bit more stiff.
I do like the stance better now. Front was way too low.

I know that a lot of ppl run them at 2.5 with no issues.
 
Hello! Just wanted to contribute to the thread. For those thinking about the TRD Grill & garnish, do it! Here's the current state of my MGM Limited. Yellow fog light bulbs, chrome delete (vinyl wrap) + TRD Grill and Garnish.

7829cb99c94a944b1d5d3113624f1b96.jpg



Sent from my iPhone using Tapatalk
 
a47chuck said:
I am, I am. Dealer had them installed when I bought it new. BFG KO2's. Also had a front end level by RevTech. There is a slight rubbing on the front of the fender liner at full lock in reverse. BFG recommends a min. 7.5" rim but the stock 20's are only 7". No ill effects on handling or ride. I'm expecting that they may wear more in the center. When they need replacing, I'll go with the SCS Stealth 6's in 17" with 265/70R's like I did on my '13 limited.

Made the liner adjustment on the '13', but too old and lazy to do the '19'. Not that bad of a rub anyway. HAH!
Click to expand...


I'll be following your progress as a fellow Oregonian with a nightshade. I haven't seen too many mods for them yet.
 
I want to add the trd grill as you did but qith the 2020 it has a.small black box in the bottom garnish do you know what is it called and wpuld I still b able to do the conversion
 
dktxt4r said:
Finished my front bumper Limited to a TRD Pro conversion this past weekend. I'm real happy with the end results. Old to New pictures below.
Click to expand...

Yes! This is exactly what I want to do to mine. How do I do this? Where did you buy your parts? Any help or advice you can give would be very much appreciated!
 
brightness20 said:
Yes! This is exactly what I want to do to mine. How do I do this? Where did you buy your parts? Any help or advice you can give would be very much appreciated!
Click to expand...


Depends if your doing the labor yourself or a shop. But to start, you can take a look at the parts comparison list. Also you can take a look at my build thread :-)
 
daytonaviolet said:
Depends if your doing the labor yourself or a shop. But to start, you can take a look at the parts comparison list. Also you can take a look at my build thread :-)
Click to expand...

Will do. I'll see if this is something my boyfriend can do. If I'm looking at a shop, do you think it'd cost hundreds or thousands? Trying to get an idea of how doable this is price wise. Thanks again!
 
brightness20 said:
Will do. I'll see if this is something my boyfriend can do. If I'm looking at a shop, do you think it'd cost hundreds or thousands? Trying to get an idea of how doable this is price wise. Thanks again!
Click to expand...


Most likely your bf can do it as it’s all plug and play. Parts and paint for the front/rear bumper ~ $1600.

This is just a rough estimate as you’ll still need a used crash bar and headlight support brackets :-)
 
You must log in or register to reply here.

Similar threads

calimobber
Lots of Mods
Replies
3
Views
2K
calimobber
calimobber
7
Seeking advice, sell modified or return to stock
Replies
4
Views
6K
MartennSie
M
M
What is the snowflake-y stuff on top of brand new Toyota pink coolant
Replies
3
Views
3K
premise
P
alirawk
New Goodies for the Rig
Replies
1
Views
1K
RO1973
RO1973
T
Can't find Lug nuts for 2025 TRD rims
Replies
2
Views
3K
2TH4IST
2TH4IST

Members online

Total: 325 (members: 6, guests: 319)

Forum statistics

Threads
278,307
Messages
3,554,049
Members
248,016
Latest member
Advally Service

Share this page

Trending content

Back
Top