Oneluv13T4R
New member
Finally got some time to cut out a fairing. The brackets were a little tricky but the Test fit was perfect and the test drive was quite. Time to paint [emoji106]
what kinda material did you use? where did you get it from?
What did you do with your 4runner today?
- Thread starter NorthGa4R
- Start date
what kinda material did you use? where did you get it from?
I just did mine two days ago on my WM rack. I wasn't as lucky on the fit. I also still have a lot of wind noise. The vibration sound is gone, but not the wind. Have you taken it up to 70+ yet?
850lifeguard
Member
24 x 40 clear acrylic sheet from Home Depot for $27. Used a oscillating cut off tool to cut the sheet. Cut through it like butter.
andy2008
New member
Yeah fill it with glue I guess it was free insurance pays for one chip repair a year. Has lifetime warranty to to spider or spread we shall see!
Put FJ coils in the rear, gained a solid inch I also put that bump stop that goes inside the coil back in as I had mistakenly tossed it away back when I originally lifted my truck. Doh! 
My son holding the old ones like captain Morgan. Lol
My son holding the old ones like captain Morgan. Lol
Attachments
Oneluv13T4R
New member
[MENTION=101553]t-man[/MENTION]
Have your son strap them around his shoe and try walking with them, or see if he can dunk with them "nike spring air's"
So now you got the rear in are you doing anything to the front tonight as well?
So you know you gained an inch what are you sitting at total in the rear now
Have your son strap them around his shoe and try walking with them, or see if he can dunk with them "nike spring air's"
So now you got the rear in are you doing anything to the front tonight as well?
So you know you gained an inch what are you sitting at total in the rear now
Oneluv13T4R
New member
Awesome thank you, and of course its from Home depot as I was just there 10 mins ago..lol
I take it you just painted it black and called it a day.
Lol, I'll tell him but I'll bet he's to chicken! Lol
I am putting a spacer in the front and lowering the Bilstein. I tried setting the shock at. 85 and putting it in with a 3" spacer but I was binding the cv up. Going good to set them at 0" tomorrow.
Also will be replacing tie rods tomorrow as mine are shot. About 1/2" of play in them now.
Will be more on my build thread too.
NinjaOne
New member
Zero Point Calibration
It rained, drop through excessively large puddles
Video of last time it rained
It rained, drop through excessively large puddles
Video of last time it rained
andy2008
New member
And you also caught proof that there are some Chevy divers with intelligence that blazer knew unless they wanted to push it home to go around that puddle haha
Oneluv13T4R
New member
Stoked and for you
cant wait for the outcome. and how it was doing the tie rods since i ordered the same kit as you from ebay. Cause my ball joints are blown out and outer tie rods blown out and with everything blown out my tires are slapping and rubbing all over in the top,front,and back of my wells bad.
So I hope yours goes well and any info/hints gained would be appreciated brotha
Will give you the full report tomorrow when I finish. The castle nut on mine looks seized, so I'll probably be cutting that out like I did the balljoints. Yay me! Lol
Slowgoat
New member
Replaced my rt rear caliper (second one, just did it in March!!!).
Jeez.
Changed to 5th Gen (had lifetime warranty, and was only 5 bucks more). One looked different, one looked exactly the same as the old one by its markings. Looked no different to my eye other than that.
It was an el cheapo Auto zone remanufactured 'Yota.
Jeez.
Changed to 5th Gen (had lifetime warranty, and was only 5 bucks more). One looked different, one looked exactly the same as the old one by its markings. Looked no different to my eye other than that.
It was an el cheapo Auto zone remanufactured 'Yota.
Last edited:
4Rnr4Evr
New member
Spent 3-4 hours cleaning this area. I cleaned the upper part of the center console a couple days ago, now I got to this. Everything you see had coke, crumbs & unidentified crap all over it, courtesy of previous owner. From a solidified pool of coke in one corner eventually emerged a paperclip
hwell: Basically removed and washed every part of the center console. Did not feel too comfortable with taking off the shifter assy so there's still some crap left, I'll leave it for some other day when I feel braver. Plus tomorrow I want to do the suspension so I don't want to get too tired.Seriously thinking about getting a new carpet.
Last edited:
NuclearN8
New member
Contemplated buying some GX460 Fsport wheels to replace the hyper silver oem wheels on my wife's 07 Limited.
Just not sure they're worth that much money... I do like the way they look though and wouldn't require us to buy new tires since the only spec difference is the Fsport wheels have 10mm more offset (F sport wheel is 20mm positive offset, 2007 4runner limited wheels are 10mm positive offset)
same wheels that are on this one: Sell used 2013 Lexus GX460 Premium 4x4 4.6L Starfire Pearl DVD F-Sport Package with Wheels in Knoxville, Tennessee, United States, for US $57,900.00
decisions decisions
Just not sure they're worth that much money... I do like the way they look though and wouldn't require us to buy new tires since the only spec difference is the Fsport wheels have 10mm more offset (F sport wheel is 20mm positive offset, 2007 4runner limited wheels are 10mm positive offset)
same wheels that are on this one: Sell used 2013 Lexus GX460 Premium 4x4 4.6L Starfire Pearl DVD F-Sport Package with Wheels in Knoxville, Tennessee, United States, for US $57,900.00
decisions decisions
riceandpho
Elite Member
Saw this b@dass runner on ifunny! They have to be on here anyone know who's it is?
he lives a few blocks from me, some of the electrical work hes done questions me, i would try to help him with some rewiring if i had the time. truck is twice as high as the owner.
Similar threads
