Fender Liner Part Number(s)

[ebg18t]

I was also looking at sheet plastic on Amazon and just cutting my own.

Amazon.com: Kydex Sheet - .028" Thick, Calcutta Black, 12"x12" 8 Pack: Industrial & Scientific

 

[scottblink23]

Left / Right Question

Front piece is different on right side. It actualy says FR on right front and FL on left. Parts on the link are fronts only, see number 9 for rear. Rear one is same for both (just flip it around).

I noticed part of my fender liner disappeared so I found this thread. Thanks for the link! My question is this ... I only need the driver's side shield, so is driver's side left or right? I apologize for the dumb question and I'll make up for it with my boss paint skills below. Thanks!

 

[Cygan1008]

I noticed part of my fender liner disappeared so I found this thread. Thanks for the link! My question is this ... I only need the driver's side shield, so is driver's side left or right? I apologize for the dumb question and I'll make up for it with my boss paint skills below. Thanks!

Left but I actually just got off the phone with toyota looking for the same parts and the two rears are the same part # so either one should work.

 

[scottblink23]

Left but I actually just got off the phone with toyota looking for the same parts and the two rears are the same part # so either one should work.

Iappreciate you! :thanks:

I'm assuming #10 represents each individual clip?

 

[momo.75]

I made the four for the front out of some material i got from McMaster Carr and they are doing great. i will see if i can find the item number.

Here is what i had used.

8513K65 - Oil-resistant Vinyl Rubber, Plain Back, 1/8" Thk, 12" X 24", 80a Durometer

http://www.mcmaster.com/#catalog/120/3553/=s9gel9

 

[Cygan1008]

I made the four for the front out of some material i got from McMaster Carr and they are doing great. i will see if i can find the item number.

Here is what i had used.

8513K65 - Oil-resistant Vinyl Rubber, Plain Back, 1/8" Thk, 12" X 24", 80a Durometer

McMaster-Carr

Did you make a templet or just kindda shove it in the feder and cut it and did you get all 4 from one 12" x 24" sheet?

 

[momo.75]

Luckily i still had mine in my fender but they were all cracked up or torn. I just used them to trace. I was able to make all four out of two sheets of that material. They look better than factory. Getting the pics off my phone now.

 

[Cygan1008]

Luckily i still had mine in my fender but they were all cracked up or torn. I just used them to trace. I was able to make all four out of two sheets of that material. They look better than factory. Getting the pics off my phone now.

Thanks for posting the link, I have been trying to figure out what material I wanted to use. This is exactly what i was looking for and the $ is right. I posted a thread looking for a templet maybe someone can help me out.

 

[momo.75]

Here are some crappy phone pics i had taken back when i made them.

 

[aburdette]

Thanks to each of you for contributing here. I just purchased a 94 4Runner that is missing these liners. I believe the truck does have a modest lift. The link to partznet that was posted early in this thread is not working for me.

Two questions -

I'm thinking about fabricating my own liners. Does anyone know what size clips I would need for the 94 4Runner?

Would these likely work in lieu of fabricating my own? I'm unsure if the "gap guards" are meant to replace stock liners or to be used in addition to them. Perf Accessories Body Lift Gap Guard - JCWhitney

Thanks!

 

[Frostythe4Runner]

Here are some crappy phone pics i had taken back when i made them.

Looks exactly like how I want mine to look, how much did it cost you I'm total? I wish I still had my old ones to trace though

 

[acronin2]

[MENTION=165]momo.75[/MENTION] any chance you the dimensions/shapes of the ones you made?? Need to do this before the winter

 

[Brutalguyracing]

[MENTION=165]momo.75[/MENTION] any chance you the dimensions/shapes of the ones you made?? Need to do this before the winter

mee too please
3 separate people told me they would send me some and nothing
i have the material sitting here ready to go
errr
anyone
i have offered $$$ as well

 

[momo.75]

Sorry but i don't have any measurements on them. If i get some free time i might could pull mine off and make some templates.

 

[RPS13]

That would be awesome. Mine went from lightly cracked to pretty much gone in a few months. The price of the factory ones is a little high given they seem to last around 6 years in TX.

 

[Brutalguyracing]

So many people here said they had templates made already
Where did they all go
I offered $$$ and they all said no just pay it forward
Id love to do that
Damit
Guess i will start tracing something soon
If i can make them i will save the templates for the rest of you guys
If they are not too big i might be able to scan them and email them out
We shall see

 

[ARK_SWAMP_RIDER]

If anyone ends up getting templates to send out, I'm in need of some as well.

 

[TORCH]

I'd also be interested in templates as well to anyone willing to send them out. Thanks.

 

[Brutalguyracing]

maybe we should each buy one from our dealerships and send the templates to the others.....

 

[Brutalguyracing]

[MENTION=165]momo.75[/MENTION] any chance you the dimensions/shapes of the ones you made?? Need to do this before the winter

Bump
Anyone