Post your LIFTED pix here!

[96706RROMJP]

Took some updated pics today.

 

[slynchrva]

Installed 5100's frond and back w/ Icon rear springs and went straight to George Washington National Park. Everything else stock.

You mean the George Washington National Forest in Virginia [MENTION=139218]Thesoundofpanic9[/MENTION]? If so, what part?

 

[Thesoundofpanic9]

You mean the George Washington National Forest in Virginia [MENTION=139218]Thesoundofpanic9[/MENTION]? If so, what part?

Yes, my bad, meant national forest. This was at Second Mountain. It was my first time in VA.

 

[kingofZroad]

Looks like a whole new vehicle now!!!


Sent from my iPhone using the "Hunt and Peck" method...

 

[Espresso01]

3in toytec coil lift. Firestone destination m/t 285 tires. Spidertrax spacers.. Quite happy with how she turned out!


2014 trail T4R

 

[cbielat]

Here's one of the latest I designed. Almost sold before I could even get it to the alignment rack. The streets need their Queens!

 

[PitbullRescuer]

^ saw it on Facebook Chris, looks good. My wife has a white SR5, I need to dress hers up.

 

[96706RROMJP]

Here's one of the latest I designed. Almost sold before I could even get it to the alignment rack. The streets need their Queens!

What kinda lift and wheel size?

 

[cbielat]

What kinda lift and wheel size?

It's just a 3"/2" Ready Lift leveling kit, 20" Ultra wheels and 275/55/20 BFG KO2 tires.

 

[pinetar]

Thank god they don't all come “designed” that way.

 

[slynchrva]

Yes, my bad, meant national forest. This was at Second Mountain. It was my first time in VA.

I knew it looked like my home state!

 

[96706RROMJP]

Woot woot! I can finally post my baby here. :hello:

Toytec 112-620 coils in front on 5100s @ 0" w/ 1/4" spacers on each side. 5100s and 1.5" Daystar spacers in the rear. About 2.25" in front now, should settle around 2" in a bit.

Got it installed by Toy-Crawlers in Broomfield, CO.

Do you know approximately how much of a lift would i get if bilstein 5100 set at .85 and went with toytec 112620s?

 

[wookiecrisp]

Do you know approximately how much of a lift would i get if bilstein 5100 set at .85 and went with toytec 112620s?

Assuming you have the same model I do, then I imagine that the 112620s (which are 1.6" higher and have a higher spring rate than OEM), will give you 1.8"-1.9" inches. (I'm at 2.25" w/ the 1/4" spacer). Add 0.85" onto that and that gives you 2.65", but that actually might get you at 3" (the same reason the 1/4" spacer yields up to 1/2").

Without actually doing it, who knows. But it would probably be close to 3". You would need UCAs too at that height unless you want a shitty ride.

But... I'm no expert in what and what can't be done, so call Toytec and ask what they think.

 

[cbielat]

Thank god they don't all come “designed” that way.

To each their own

 

[Da8ron]

Thank god they don't all come “designed” that way.

Haha BRUTAL!

Sent from my SM-G900V using Tapatalk

 

[96706RROMJP]

It's just a 3"/2" Ready Lift leveling kit, 20" Ultra wheels and 275/55/20 BFG KO2 tires.

Did you have to replace the UCAs?

 

[cbielat]

Did you have to replace the UCAs?

No, it's all factory still. The control arms would help getting back to factory alignment specs but it's not far off. For just street use it's fine.

 

[cbielat]

Thank god they don't all come “designed” that way.

What, you don't like the 20s and leveling kit? lol

 

[pinetar]

What, you don't like the 20s and leveling kit? lol

 

[cbielat]

Don't know what you're missing out on.