Magnuson Supercharger for 2010-Present & 2010-2014 FJ

I don't understand why they would ever post this picture. its IS scary looking probably to most.[/QUOTE]

I think they're banking on the idea that "any press is good press". But yes, scary looking nest of wires!
 
marshal said:
The latest from Gadget with the Whipple kit. Also to let you know how big of a ***** getting to your ECM is
Click to expand...

If I remember correctly, getting the ECM out is not big deal at all. You remove the kick panel and it is right there... with pretty easy access. All that mess is not the stock ECU.
 
Another update from gadget
 

Attachments

  • IMG_6592.jpg
    IMG_6592.jpg
    130 KB · Views: 999

Attachments

  • UCONMounted2200.jpg
    UCONMounted2200.jpg
    7.8 KB · Views: 940
Please create new thread for URD products. I would hate to get information confused and mixed around. A new Magnuson unit will be going on very soon and I will provide info.
 
For those that had issues with sourcing the ECM, when hooking up most scan tools the ECM will pop up as two CAL I'd. Let me know if you continue to still have issues. It's important to have those placed on the application. A lot of content and info coming tomorrow.
 
THESS said:
Please create new thread for URD products. I would hate to get information confused and mixed around. A new Magnuson unit will be going on very soon and I will provide info.
Click to expand...

Slightly off-topic, they ever mention if they were going to redo thee 4.7L 2UZ-FE Blowers? :becky:
 
THESS said:
For those that had issues with sourcing the ECM, when hooking up most scan tools the ECM will pop up as two CAL I'd. Let me know if you continue to still have issues. It's important to have those placed on the application. A lot of content and info coming tomorrow.
Click to expand...

I lost the old HD I had TIS running on and I can't seem to get it to install and connect on 64bit... my other scan tool will not show the cal ID... So I'm SOL right now. I even purchased another cable thinking that might be it... but no dice. I'm sure I can eventually get TIS running again, but I need time to either find more hardware or get a VM up that can support it. PITA for sure. Anti-Virus not linking any of the drivers...
 
wfo9 said:
I lost the old HD I had TIS running on and I can't seem to get it to install and connect on 64bit... my other scan tool will not show the cal ID... So I'm SOL right now. I even purchased another cable thinking that might be it... but no dice. I'm sure I can eventually get TIS running again, but I need time to either find more hardware or get a VM up that can support it. PITA for sure. Anti-Virus not linking any of the drivers...
Click to expand...

I ended up installing a VM on my 64bit laptop. Works flawlessly now.
 
That picture reminds me of what it looks like when wiring in a Megasquirt or similar ECU. Definitely not something you would see from a completed package.

wfo9 said:
If I remember correctly, getting the ECM out is not big deal at all. You remove the kick panel and it is right there... with pretty easy access. All that mess is not the stock ECU.
Click to expand...
 
THESS said:
For those that had issues with sourcing the ECM, when hooking up most scan tools the ECM will pop up as two CAL I'd. Let me know if you continue to still have issues. It's important to have those placed on the application. A lot of content and info coming tomorrow.
Click to expand...

So, I finally got Toyota TIS up and running on a VM. I found the calID for the ECM on the stored data screen. But I can't find the ECM P/N. Anyone know the screen and how to navigate to it.

[MENTION=139149]THESS[/MENTION]
[MENTION=66389]BlackWorksInc[/MENTION]

any ideas.

They are asking for calID and ECM P/N.. Says usually listed on the vehicle ID screen.
 
Last edited:
wfo9 said:
So, I finally got Toyota TIS up and running on a VM. I found the calID for the ECM on the stored data screen. But I can't find the ECM P/N. Anyone know the screen and how to navigate to it.

[MENTION=139149]THESS[/MENTION]
[MENTION=66389]BlackWorksInc[/MENTION]

any ideas.

They are asking for calID and ECM P/N.. Says usually listed on the vehicle ID screen.
Click to expand...

Ah, crap... Uhm... It should be there when you're looking at the calibration page. I haven't bothered looking at the part number through TIS because usually I'll just snag it off the ECM itself if I need it.

I'll try and remember to play around with it tomorrow at work and see if I can get you a solid answer. :(
 
I can tell this much about the graph for sure.

The lines cross at 5252 :first:.

The tq is 30x
The HP is 3xx

It's a chassis dyno, stock they usually are in the 240tq/220hp range.. 350hp is all I ever wanted and it will obviously stomp a v8 GX in terms of acceleration... not that it matters, but something to measure up against on the same platform.

Seems like things will net out near the +100 flywheel hp/tq range. Close to +35% which is very good for a conservative boost setup.

I'm excited to put one on and turn up the smile meter. :beer:
 
Last edited:
@WFO9

Checked today and don't see an option to get P/N of the ECM through TIS, gonna have to get it manually off the side of the ECM. Sorry mate.
 
You must log in or register to reply here.

Similar threads

2TH4IST
E-Fan swap.
2
Replies
32
Views
12K
kwerfybertface
K
Moist
V8 Hypermiling Guide
Replies
4
Views
4K
FrontRange4
FrontRange4
L
New to Me 2010 SR5
Replies
19
Views
4K
rigtec
rigtec
PJSnow
Team Tech Offroad (TTO) - Scan Gauge Custom Housing
Replies
6
Views
10K
honda250xtitan
H
PJSnow
Lasfit 3" LED Pod Ditch Light Kit (and Ditch Light Options Overview)
Replies
7
Views
10K
PJSnow
PJSnow

Members online

Total: 4,903 (members: 1, guests: 4,902)

Forum statistics

Threads
278,317
Messages
3,554,129
Members
248,016
Latest member
Advally Service

Share this page

Trending content

Back
Top